Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
When not looping through, set this switch to ON. 23. Video Output Connector (VIDEO 1,2) A 1.0V[p-p]/75 Q. composite video signal is provided at this connector. 7 24. S-Video Output Connector (S-VIDEO OUT) The luminance (Y) and chrominance (C) signals for VCR or monitor are provided at this connector. S-VIDEO OUT (Mini-DIN,4-pin) Pin No. Description 1 Y Ground 2 C Ground 3 Y Signal Output (0.714V[p-p](Y level)/75 O) 4 C Signal Output (0.286V[p-p](Burst Level)/75 ii) 26. RS-232C Connector (RS-232C) S 6-9 Pin No Signal RS-232C 1 Ground 2 TXD 3 RXD 4 DSR 5 Ground 6 DTR 7 CTS 8 RTS 9 Ground 25. RGB/SYNC Output Connector (RGB/SYNC) The red, green, blue, sync and composite video signals are provided at this connector. Note: Refer this connection to a qualified service parson or system installer. 27. 12V DC Input Terminals (12V DC IN) These terminals accept an external DC power source supplying nominal power of 12V DC, 0.7A. RGB/SYNC (D-SUB,9-pin) $ $ © [§] « Pin No. Description 1 Ground( GND) 2 Ground (GND) 3 Red (R) Output (0.7V[p-p]/75 Q) 4 Green (G) Output (0.7V[p-p]/75 fi) 5 Blue (B) Output (0.7V[p-p]/75 Q) 6 Composite Video Output (1.0V[p-p]/75 ft) 7 Sync (SYNC) Output (4.0V[p-p) or 0.3V[p-p]/75 ß) 8 Ground (GND) 9 Ground (GND) Cautions : 1. Connect to 12V DC (11.5 V - 16 V) class 2 power supply only. 2. To prevent fire or electric shock hazard, use a UL listed wire VW-1, Style 1007 cable for 12 V DC input terminals. 8 CONNECTIONS Cautions : 1. Keep the DC POWER ON/OFF switch in the OFF position until all connections have been properly made. 2. Connect the camera head and camera control unit. Internal Sync Operation 1. Connect the camera cable between the camera head and the camera control unit. 2. Connect the coaxial cable with BNC connectors between the video output connector of the camera control unit and the video monitor or VCR. Gen-lock Operation 1. Connect the camera cable between the camera head and the camera control unit. 2. Connect the coaxial cable with BNC connectors between the video output connector of the camera control unit and the video input connector of Special Effects Generator (SEG), and between the VBS/HD input connector of the camera control unit. ccu Video Monitor VCR or Video Monitor Coaxial Cable VIDEO VIDEO 75121_BjHi-Z 75ÍJJI_|Hi-Z © "* © «-m- * © IN OUT IN OUT CCU vs&ho yd I VTCÍO 2 A 3. Connect the power cable between the DC 12 V input terminals and the 12 V DC power supply unit (obtained locally). • The maximum cable length between camera control unit and power supply unit is calculated as follows: 11.5 V DC < Va - (R x 0.42 x L) < 16 V DC L : Cable length (meter) R : Resistance of copper wire (fi/meter) V*: DC output voltage of power supply unit L standard = V* - 12 / 0.42 x R (meter) L minimum = V* - 16 / 0.42 x R (meter) L maximum = Va - 11.5 / 0.42 x R (meter) 3. Connect the power cable between the DC 12 V input terminals and the 12V DC power supply unit (obtained locally). Cautions : 1. Connect to 12 V DC (11.5 V * 16 V) class 2 power supply only. 2. To prevent fire or electric shock hazard, use a UL listed wire VW-1, Style 1007 cable for 12 V DC input terminals. Cautions : 1. Connect to 12 V DC (11.5 V - 16 V) class 2 power supply only. 2. To prevent fire or electric shock hazard, use a UL listed wire VW-1, Style 1007 cable for 12 V DC input terminals. 9 Mounting the Lens Caution : Keep the POWER ON/OFF switch of the camera control unit in the OFF position throughout the installation. Lens Mount 1. Remove the front cap of the camera head and confirm that the surface of the optical filter of the camera head is clean. If the surface of the optical filter is dirty clean it with a blower brush which is for film camera lenses (available at your local camera store). 2. Mount the C-mount lens by turning it clockwise onto the lens mount of the camera head. Cautions: • Do not use any lens which has more than 1/8" (3.5mm) of protrusion for lens mounting. (GP-US522) • Do not open the lens iris wider than the F2.8 stops. (GP-US522) • Do not open the lens iris wider than the F2.2 stops. (GP-US532) o o o Special C-mount: Less than 1/8” (Less than 3.5mm) 10 SETUP 1. CAMERA SETUP MENU This camera utilizes a user setup menu that is displayed on-screen. The setup menu contains various items that form a tree-type structures as shown below. It is described in the following section: “2. SETUP OPERATION". Note: The SETUP menu is output from the VIDEO 1, 2 connectors, the S-VIDEO OUT connector, and the RGB/SYNC connector. SET UP MENU Camera ID ON/OFF Camera ID Editing Camera ID Display Position Manual Area Setting Scene File PAGE 1 PAGE 2 2. SETUP OPERATION This camera utilizes a user setup menu (SETUP) that is displayed on the monitor. To set items on the SETUP menu, use the following buttons on the front panel of the camera control unit. Page Bu...