Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
0) 1.1 NnwtiiHy C'o*#a IN C) í ntactson this Doard ** No DosgnaioP PwNo Омф>«до Э7 Grorö 19 Air** If » Qrxrc il AT" '• » 4or uaad 17 Ai»«» t? •tt лес * AT» Il » NoiiMC tS AT"» * » lu— 32 14 AT** 14 13 || » V»— X 12 AMT t| 9 Mr-29 11 Дат» il at Aar*» 25 « Av* «0 »Лёг-27 9 AT- t Я Ж. y— • Ат* • » rtj— 25 ? M Alar-2* i Ат-ê a Av«Z3 S Ат** I a Ат— 22 « Мая» 4 ft Aip-r a Air* I » ATMS 2 i АП» 1 =®= -1- ■ Board Setting Before installing this board, the following settings should be made by qualified service personnel or system installers. 1. Set switches (SW1 and SW2) on the board to designate the Alarm Output board number as shown in the following table. The factory default setting is Board Number 1 (00). Board No. Alarm Output SW Positions SW2 SW1 1 1-32 0 0 2 33-64 0 1 3 65-96 0 2 4 97- 128 0 3 5 129- 160 0 4 6 161 - 192 0 5 7 193- 224 0 6 8 225 - 256 0 7 9 257 - 288 0 8 10 289 - 320 0 9 11 321 - 352 0 A 12 353 - 384 0 B 13 385-416 0 C 14 417 - 448 0 D 15 449 - 480 0 E 16 481 - 512 0 F -2- 2. Position jumper connectors (CN10, CN50, CN90, CN130. CN170, CN210, CN250, and CN290) on the board to meet the alarm output requirements. Select either Normally Open (N.O) or Normally Closed (N.C) for the contact output, and then confirm that the jumper connectors are positioned at Ground (GND) as shown below. The factory default settings are Normally Open (N.O). Vo ro ho l\i k> ro ro rvj' oooooooo CN210 Normally Open (N.O) Default Setting Normally Closed (N.C) Ground (GND) Default Setting Installation The following installation should be made by qualified service personnel or system installers. • Installing Additional Extension Boards 1. Remove the screws from the rear panel(s) of the WJ-SX850 Matrix Switcher Card Cage. 3. Confirm that the jumper connector (CN4) on the board is positioned on 1 and 2. This setting lets you select the output polarity. CN4 flNVl NOR I 3 1 | Polarity] Default Setting 2. Remove the rear panel(s). 3. Remove the front panel of the cage by removing the two screws on the panel shown below. -3- 4. Place the Boards into the specified positions in the front or rear of the Cage by sliding them along the board guides as shown below. 5. Make sure to push in the Boards until they are seated firmly. 6. Secure the rear board by tightening the two screws on the board. 7. Close open spaces on the rear of the Cage with the supplied rear panel(s). 8. Close the front of the cage by fixing the front panel. Specifications Alarm Output (1 - 32): Dimensions: Weight: 24V DC 500 mA maximum Normally Open or Normally Closed selectable 37-pin D-sub connector Front Board; Rear Board; 0.5 kg (1.1 lbs) 255(W) X 250(H) X 12(D) mm 10-1/16*'(W) X 9-13/16"(H) X 1/2"(D) 117.5(W) X 265(H) X 20(D) mm 4-5/8"(W) X 10-7/16"(H) X 13/16”(D) Weight and dimensions indicated are approximate. Specifications are subject to change without notice. Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario. L4W 2T3 Canada (905)624-5010 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc. Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 (809)750-4300 © Matsushita Communication Industrial Co., Ltd. 1999 NM1099-0 YWV8QA5060AN Printed in Japan (N) 19...