The camera continuously measures the color temperature of the light source and automatically adjusts the white balance. The adjustment of the color temperature ranges from approx. 2 700 K to 6 000 K. AWC: Activates the automatic white balance control mode. This adjustment is suitable for a location where a light source is stable. The adjustment of the color temperature ranges from approx. 2 000 K to 10 000 K. Default setting:ATW • Synchronization mode selector[INT/LL] Selects the camera synchronization mode as either internal sync mode (INT) or line- lock mode (LL). INT: Sets to internal 2:1 interlace LL: Sets to line-lock mode Default setting: INT Note: • Please use the INT setting when DC 12 V is used (WV-CP294). 12 Installation and Connection 1 Rotate the lens (option) clockwise slowly to mount the lens. Important: • For use of C-mount lens, use the C-mount adaptor (option). • For prevention of damage to the camera body, use a lens with protrusion of 5.5 mm or less from the flange surface. Optional dedicated lens Protrusion from flange: 5.5 mm or less Protrusion from mount: o20 mm or less Caution: • Be sure to connect the grounding lead to the GND terminal (WV-CP290). Lens type Model No. ALC lens for 1/3 inch CCD cameras 2x vari-focal WV-LZA61/2S WV-LZA62/8S 13 Pin No. 1 Dump 2 Dump 3 Drive 4 Drive ALC lens connector 1 3 2 4 Screws (locally procured) Screws (locally procured) Camera mount bracket (option) 2 Connect the lens cable to the ALC lens connector of the camera. 3 Secure the camera mount bracket (option) to an installation position, and mount the camera on the camera mount bracket. Important: • The camera mount bracket shall be mounted on the foundation part of the construction or a part with adequate strength. • Recommended screw M6, minimum pull-out strength196 N. • The other security measures to prevent dropping also must be considered when the total weight of camera and its lens is above 1 kg in addition to the fall protection measure functioned by coaxial cable, in order to strengthen the fall protection countermeasure. (The fall protection measure can be functioned through the coaxial cable when the total weight is below 1 kg.) Orificio roscado para tripode: 1/4-20 UNC para tripode Base de montaje de tripode Tornillos de montaje • When attaching an optional tripod mount base on the bottom of the camera, use the removed screws to attach the tripod mount base. Use of longer or shorter screws may cause drop or damage. Recommended tightening torque: 0.39 N·m 14 4 The coaxial cable(procured locally) is connected to this video output connector. Important: • Be sure to turn off the power of each device before connection. • Be sure to secure the coaxial cable connectors. Connect a coaxial cable to the video output connector. 5 Use a cable tie (locally procured) to attach the coaxial cable to the camera mount bracket. Important: • The cable tie shall be made of metallic or durable material to be strong enough because the tie plays the role of camera drop prevention measures in case. • When the camera mount bracket is mounted on a wall, be sure to observe the mounting height described on the illustration below. To video input Coaxial cables WV-CP290 AC IN 220 - 240V INT ATW ON ON . . ON D/N BLC LL OFF AWC OFF OFF ~50Hz VIDEO OUT BS Camera mount bracket (option) The cable shall be tied to the camera mount bracket to avoid slack. The cable shall be tied to the camera mount bracket to avoid slack. Camera mount bracket (option) More than 270 cm Floor _ 6Turn on the power. WV-CP290 The included power cord is connected to this power connector. Connect between the power connector on the rear side of the camera and a plug socket with the supplied power cord. 220 to 240 V AC, 50 Hz 220 -240V ~ 50 Hz I N T A T W O N O N . . O N B L C D/ N L L A W C O F F O F F O F F .... VIDEOOUTBSAC IN Power cord (accessory) Caution: • The camera shall be connected with cord set with plug. Plug for respective country shall be mounted on the Power cord by a qualified electrical. WV-CP294 Important: • The power supply of 24 V AC/12 V DC shall be insulated against 220 to 240 V AC. • The power supply is automatically selected either 24 V AC or 12 V DC. No setting is required with this camera. A Loosen the screw of the power cord plug (accessory). B Connect the power supply (option) of 24 V AC or 12 V DC to the power cord plug. Strip the end of the wire by 3 mm to 7 mm, and twist the stripped part of the wire sufficiently to avoid short circuit. • Specification of cable (wire) AWG #16 - #28, Single core, twisted * Check whether the stripped part of the wire is not exposed and is securely connected. 24 V AC 12 V DC A 2-N (GND) B GND NC C 1-L C Tighten the screw of the power cord plug. D Connect the power cord plug to the AC/ DC power terminal on the rear side of the camera. * Make sure that the power cord plug is inserted...
)
