Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
B A OUT IN-2 IN-1 100/10BT VIDEO OUT LINE IN DC IN 12-13V AC IN 24V LINE OUT Notebook PC HUB (Rear) AC power cable AC Adapter LAN cable When using the AC Adapter (Optional) or external power supply The figure shows the AC adapter (optional). Connect the Camera to the Network and Perform the Initial Setting Note .Please ask our sales person for PoE HUB and Midspan. .Read the manual of the PoE HUB or Midspan for how to use it. .Up to 100 m of the LAN cable can be connected between the camera and the PoE HUB. .Use a shielded LAN (Categrory 5 or above) cable for VB-C300 connection. .If the camera is connected to a switching HUB and connection is changed while the camera is operating, the learning capability of the HUB may disturb the communication. Do not change connection while the camera is operating. Turning the Power ON and OFF The VB-C300 itself does not have a power switch. If the power is supplied to the VB-C300 via a LAN cable using the PoE function, connect anddisconnect the LAN cable from the camera to an operating HUB to turn the power ON and OFF. Installing the Camera When using PoE HUB LAN cable PoE HUB VB-C300 When using the AC adapter (optional) or external power supply, the camera is powered ON by plugging the AC adapter (optional) or external power supply. When using the AC Adapter (Optional) or external power supply AC power cable AC Adapter VB-C300 100-240VAC 50/60Hz The figure shows the AC adapter (optional). 2-5 Connect the Camera to the Network and Perform the Initial Setting When using external power supply When using external power supply, use the Power Connector (> P.vi) supplied with the camera as shown to the right. Supply 12VDC or 24VAC from a power supply insulated from 100-240VAC supply. You can connect 12VDC power supply without regard to the polarity. When using an external power supply, make sure that the voltage falls within the ranges below. AC24V: Voltage fluctuation within AC24V±10% Current supply capability over 1.0A per camera DC12V: Voltage fluctuation within DC12V±10% Current supply capability over 1.5A per camera Screwdriver Stripping length approx. 4mm - 6mm (0.16inch - 0.24inch) Power Connector (Supplied) * If using a DC12V battery power source, make sure to use the DC12V by connecting a resistor that is between 0.5 and 1.0., and over 20W in series to the power supply line. Recommended power supply cables for VB-C300 [for reference] Cable (AWG) Conductor diameter (omm) #24 (0.52mm) (0.020inch) #22 (0.65mm) (0.026inch) #20 (0.82mm) (0.032inch) #18 (1.03mm) (0.041inch) #16 (1.30mm) (0.051inch) 12VDC Maximum cable length (m) Maximum cable length (ft) 5 16.4 9 29.5 14 45.9 23 75.4 32 105.0 24VAC Maximum cable length (m) Maximum cable length (ft) 11 36.1 18 59.0 29 95.1 46 151.0 64 210.0 Use a UL cable (equivalent to UL-1015) as the power cable for 12VDC or 24VAC. The network connection is now complete. Note .The camera head position is automatically initialized when the power supply is turned ON. .Never touch the camera head while its position is being initialized. If you touch it, the head position may not be initialized correctly, or other malfunctions may result. .Wait at least 5 seconds before turning the power back on after shutting it off. Turning it on too quickly may result in a malfunction. Observe the precautions given in “Safe Use of Equipment/IMPORTANT SAFETY INSTRUCTIONS (> P.viii, x), “Safe Use of Equipment/When using the camera with PoE HUB (> P.xii) when plugging and unplugging the power cable. .Read the manual of the PoE HUB for how to power it ON or OFF. .You can connect the AC adapter (optional) to the camera while it is powered from the PoE HUB. In this case, the PoE-supplied power is used while it is active, and the power from the AC adapter (optional) is not used. When the PoE-supplied power is disconnected, the power supply automatically switches to the AC adapter (optional). 2-7 Installing the Camera Installation Example 1. Insert the supplied Setup CD-ROM into your PC, and double-click “VBSetup.exe” from Explorer to start the VB Initial Setup Tool. Initial setting of the Camera The instructions here assumes that a single camera is connected to a PC as an example. LAN cable HUB VB-C300 Supplied Setup CD-ROM Continued on the following page. a Connect the Camera to the Network and Perform the Initial Setting Connect the Camera to the Network and Perform the Initial Setting 2. The VB Initial Setup Tool automatically detects the camera connected to the network, and displays its MAC address, IP address, and model name. The factory default IP address is set to “192.168.100.1” The MAC address can be found on the label attached on the bottom of the unit. Note that VB Initial Setup Tool (VBSetup.exe) cannot be used across subnets. Click the MAC address to select it, and click “Initial Setup”. 3. Enter the user name “root” and the factory default password “VB-C300” (case sensitive) then enter the IP address and subnet mask. If you do not want to specify a ...