Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
DI : 0 ~ 12V(with 5V logic trigger) / 20 mA(minimum) DO: 30VDC / 1A - Page 13 - - NSC3621 - Warm Reboot Factory Default +_ 10x optical / 10 digital CCD DIDO Connector Same as NSC3615 DIDO interface. DI : 0 ~ 12V(with 5V logic trigger) / 20 mA(minimum) DO: 30VDC / 1A - Page 14 - System Requirement Before you give surveillance camera a shot, please check setting of your notebook / PC and see if following requirement is proper. • Windows XP with service pack 2 installed or DirectX 9.0 installed • Best Screen Resolution : 1024x768 • Color Quality : full color (32 bit) Hardware Installation - NSC3615 - - Page 15 - -NSC3621- Software Installation Follow the procedures describe bellows to do a quick installation setup / test. 1. Device Connection: Connect your surveillance camera to PC (NSC3621 is taken as an example) - Page 16 - i) Use crossover ethernet cable: ii) Connect devices with ethernet hub / switch (normal RJ-45 cable) 2. Configure your PC to the same subnet segment of surveillance camera. i) The camera’s default IP is 192.168.0.100. We need to change our PC’s network setting first in order to connect to the camera. PS: if you don’t know how to reset surveillance camera to factory default, please refer to Factory Default Setting section of Appendix FAQ part. ii) Clicks windows Control Panel.. Network Connections .. Local Area Connection, click mouse right button and then click Properties - Page 17 - iii) Chooses Internet Protocol (TCP/IP), and then click Properties iv) Chooses Use the following IP addresses, field, and input IP address with 192.168.0.139, subnet mask with 255.255.255.0, and then click OK. - Page 18 - v) Verify the on-line status of your surveillance camera. Please follow the procedure bellows a) Start Program• Accessories • Command Prompt .A DOS command shell screen will appear and shows "C:\>". b) Type ipconfig and press Enter. c) check if you can get the response from surveillance camera. d) Type ping 192.168.0.100 and press Enter. If the screen shows Reply from 192.168.0.100... it means the hardware installation is complete. 3. Connect to camera - Page 19 - i) Launches Microsoft Internet Explorer and type URL: then you shall see the home page like bellows. ii) The default username/ password is admin / admin, after you login to web you can get the video and find the system version on the lower-left corner For the very first time, IE will ask for user to download a video / audio decoder (a.k.a. ActiveX control) plug-in. Beware of the reminding message on upper-left corner of IE. Right click on the warning message and allow the plug-in to be installed in your PC. - Page 20 - Click the Install button to start installation of decoder plug-in. The live video will be displayed on IE after the plug-in automatically installed. In some case, your local PC may turn on the firewall option and the following warning message will pop up. Remember to click Unblock to allow the in-coming packet and avoid firewall protection. - Page 21 - Note: In order to turn off the firewall protection, you can refer to Control Panel .. Windows Firewall .. General and turn off the Windows Firewall and permit the in-coming network packets (audio or video media packets) - Page 22 - Otherwise, you can discriminately allow specific application and automatically unblock the firewall protection. You can check current firewall protection option of your network setting. If the network connection icon comes with a lock sign, that means the network interface is firewall protected by Windows Firewall. - Page 23 - - Page 24 - Restore to factory default If the system is up and running, you can push factory default button through pinhole of surveillance camera (marked as Restore default, the Reset is used to perform a warm system reboot). The firmware will recover the setting to factory default.The following configuration is the firmware factory default setting: Default IP Setting IP mode: Fixed IP IP address: 192.168.0.100 Subnet mask: 255.255.255.0 Webs Default User Account Username: admin Password: admin - Page 25 - Installing Scan Utility The following procedures guide you through the steps of scan utility installation and operation: Step 1 : Visit WinPcap and download WinPcap version 3.1 from the website: Step 2 : Install WinPcap version 3.1(Installer for Windows / WinPcap_3_1.exe). i) Double click WinPcap_3_1.exe icon. ii) Click Next to continue. iii) Click I Agree to continue. - Page 26 - iv) Click Finish to complete installation. Step 3 : Launch Scan Utility and Assign new IP address to surveillance camera - Page 27 - i) Double click the scan utility iiap.exe ii) Click Scan button to send out scan packet to the LAN. iii) The found devices will be displayed on lower panel of utility program. The Status field shows you whether the device is ON LINE(configured in same subnet) or IDLE(not configured properly in the same subnet). If you want to modify the network setting of specific...
Este manual também é adequado para os modelos :Vídeo - NSC 3621 PTZ Network surveillance Camera (3.79 mb)