Assessments - , GPA: ( )

Instruções de Operação Crimestopper Security Products, Modelo RS801

Fabricante : Crimestopper Security Products
Arquivo Tamanho: 28.79 kb
Arquivo Nome : rs800_1_ops.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start". 2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER ATTEMPTS WILL BE MADE AUTOMATICALLY TURNING OFF A REMOTE STARTED ENGINE: 1) Engine is running in Remote Start (Parking lights are ON). 2) Press the Remote Start button again or for RS801 model, activate Green Start input wire. 3) Engine turns & parking lights OFF, Doors remain locked or will re-lock/re-arm if applicable. CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL WITH RS800) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) through the transmitter for safety and convenience. This feature may require extra labor and/or parts to install. REMOTE LOCK / UNLOCK (RS-800 ONLY) 1) Press the Lock/Unlock button on the transmitter as you leave or come near the vehicle. 2) Parking lights will flash once for lock and twice for unlock. If vehicle is remote started, engine will remain running and lights will flash but return to solid indicating engine is still being controlled by the remote starter. NOTES: Doors lock automatically when vehicle is Remote Started. Starter Disable/Anti-grind is also enabled/disabled with the lock/unlock button. If an anti-grind/starter kill relay is installed on a vehicle without power door locks, the lock/unlock button of the remote control must still be used to operate the Starter disable. VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode. The keyless entry will still function normally while in valet mode. In the event of a lost or broken transmitter, perform this step to override the Starter Disable (If installed). CONVENIENCE AND SAFETY FEATURES CONVENIENCE AND SAFETY FEATURES HOOD OPEN SAFETY SWITCH Prevents the engine being Remote Started when hood is open and will abort a remote start if running. Eliminates risk of injury to someone working under the hood of the vehicle. If a Remote Start is requested with the hood open, the lights will flash twice, Ignition will not turn on, and the unit will not attempt a start. BRAKE PEDAL RESET CIRCUITRY Prevents starting or shuts off a remote started vehicle when this circuit is active or activated. Prevents unauthorized tampering. This circuit shuts the system down immediately when brake pedal is pressed if key is not in ignition and turned to the RUN position. ANTI-GRIND / STARTER DISABLE Prevents the driver from accidentally grinding the starter if the Ignition key is turned too far (to the start position) while engine is already running from the remote starter. Starter circuit is automatically disabled when doors are locked using remote (RS800 model only) as an added security feature. NOTE: In the event of a major malfunction, performing electrical service or jumpstarting the vehicle you should remove the main Power Fuse(s) to protect the unit from possible damage. TRANSMITTER PROGRAMMING (RS800ER ONLY) TRANSMITTER PROGRAMMING: Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4 different transmitter codes. 1. Open Hood. 2. Turn key to the ON position. 3. Press Programming button 4 times. After a few seconds, the unit will flash the parking lights 4 times. 4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and 4 flashes for the 4th code. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 SOUTH TAPO ST. SIMI VALLEY, CA. 93063 RS800...