Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
The Passive Infra-Red sensor detects movement of people and vehicles, while allowing small animals to pass through undetected. The PIR Motion Sensor has a built-in microphone and speaker that allows for communication between the Base Station and the Sensor. When the PIR Motion Sensor detects movement a signal is sent to the base station which alerts the homeowner with sounds and lights. The Alert can also remotely control a low voltage electrical device near the PIR Motion Sensor like a light or a camera (See Advanced Features). Passive Infra-Red (PIR) Motion Sensor Swivel Bushing Mounting Plate Operation & Features On/Off: To turn Base Station OFF hold down the Volume button until a beep is heard and light goes out. To turn Base Station ON press the Talk button. Volume ButtonPIR Sensor/Test Light Speaker Talk (Power - On) Remote Activation Button Learn Button Switch #1: Mute Switch #2: Tone AC Adapter Relay Output Contacts Base Station (not provided) PIR Motion Sensor Carton Inventory Intercom Feature: When PIR Motion Sensor has detected motion, the Base Station will allow you to listen through the PIR Motion Sensor for 10 seconds. If you wish to talk to the person on the other end, hold down the Talk button and speak, releasing it to hear. Volume: Pressing the Volume button repeatedly will cycle through volume levels. Mute: To temporarily mute Base Station, hold the Volume and Talk buttons down for three seconds. The Base Station will reactivate after one hour, or by pressing the Talk button. Remote Button: If there is an accessory device connected to the relay on the PIR Motion Sensor, it can be activated by pressing the Remote button within 30 seconds of the signal from the alert buzzer. Switch #1: Switch #2: Battery: The AA Alkaline batteries (not provided) will last up to 2 years depending on use (Lithium batteries recommended for colder environments). If PIR Motion Sensor batteries are low Base Station will emit three high-pitch beeps every ten minutes. If Base Station batteries are low it will emit two high-pitch beeps. Clear Memory: Press and hold the Learn button on the Base Station until 3 beeps are heard. If the PIR Motion Sensor signals while Learn button is pressed, repeat the procedure. Programming Additional PIR Motion Sensors: Each Base Station can learn the code of up to 8 PIR Motion Sensors, responding with multiple buzzes. To program additional PIR Motion Sensors see Step 6. 1 2 ON OFF OFF Buzzer Off ON Buzzer On (Default) OFF Long Buzz ON Short Buzz (Default) To prevent possible SERIOUS INJURY or DEATH from electrocution, outputs are suitable ONLY for controlling low voltage devices, 24V max, ac or dc. 1 2 PIR Motion Sensor Assembly & Test Connect the PIR Motion Sensor box to mounting plate with silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. A Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) B Ensure batteries do not touch circuit board. Test the PIR Motion Sensor by waving hand in front of sensor. Test light should flash after several seconds. Ensure Base Station (not provided) has power. A Ensure that Base Station and PIR Motion Sensor are in close proximity to each other. Press and release learn button on Base Station. Buzzer will sound. Mount PIR Motion Sensor vertically on solid surface a few feet off the ground and within 1000' of Base Station. Unit should be able to swivel as needed. OPTIONAL A B NOTE: Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. Secure cover with the two large black screws. B Within 5 seconds, wave hand in front of PIR Motion Sensor. Test light will illuminate and Base Station will activate with static and feedback after several seconds. 3' - 5' 10' - 20' Programming PIR Motion Sensor to Base Station PIR Motion Sensor Installation A B Vehicle Alert Installation: For cars, the best mounting position is about 4' high, between 10-20' back, and angled to see the back of car after passing the sensor. Step 1 Step 2 Step 3 Step 5 Step 6 Step 7 Step 4 Advanced Features Both the PIR Motion Sensor and Base Station have relays which can activate other electrical devices. The accessory device will need a separate power supply. NOTE: Output switching capacity is low voltage (24V max, ac or dc). Base Station: The relays can be used to activate louder alarm bells, lights, cameras, or other accessories. PIR Motion Sensor: The relays will only activate when the remote button is pressed on the Base Station. To prevent access to these relays flush mount the PIR Motion Sensor. Troubleshooting The Alert does not function. Check batteries in PIR Motion Sensor. Ensure Base Station has power. Ensure PIR Motion Sensor is programmed to Base Station. The Alert is not getting expected transmission range. Ensure Base Station antenna is vertical and keep PIR Motion Sensor away from trees and metal objects. Ensure Base Station is...