Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Model WKP5LM can hold up to 5 PIN Numbers. Model WKP250LM can hold up to 250 PIN Numbers. Assembly Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Keypad will beep. Keypad will continuously beep indicating no Master PIN Number has been programmed. Proceed to Initial Setup. Keypad Initial Setup Step 1: On keypad press: Step 2: Enter 4 digit Master PIN Number. Example: 1234. ?? Multiple Keypads at Same Location Step 1: On secondary Keypad enter Master PIN Number: ?? Step 2: Then: NOTE: To switch a secondary Keypad to a Main Keypad, enter the Master PIN Number followed by “57”. Step 3: On Main Keypad enter Master PIN Number: ?? Step 4: Then: NOTE: If a siren noise is heard the programming has failed. Repeat process. NOTE: This step applies only if more than one Keypad is being used. Bolt (4) Washer (4) Nut (4) Screw (4) Allen Wrench NOTE: “ * “ is the cancel button that will cancel any call or key sequence. The Keypad can be used as a primary or secondary device. Accessories should be programmed directly to the primary device. ### ?? ?? 56?? 05 1 Operation Enter existing Master PIN Number on Keypad: ???? 09### Enter new Master PIN Number: Change Master PIN Number “BEEP” “BEEP” To use Keypad, enter any valid PIN Number. With multiple Receivers, enter the PIN Number followed by the Receiver Identity (1-4). Pre-Installed Liftmaster Receiver Step 1: Pry open the front panel of the receiver case with a coin or a screwdriver. Step 2: Press and release the Learn button on the receiver. The Indicator Light will light for 30 seconds indicating that receiver is in Learn Mode. Step 3: Within 30 seconds enter Master PIN Number on Keypad. Step 4: Press “1”. Repeat Steps 2-4 for each remote, or control device that will be used to access the Liftmaster door or gate operator. Erase All Control Codes Press and hold the Learn button on the receiver until the Indicator Light turns off indicating that the receiver memory is clear (about 6 seconds). Indicator Light Learn Button A temporary PIN Number can be used only once within a 24 hour period. NOTE: The WKP5LM can hold up to 5 Temporary PIN Numbers while the WKP250LM can hold 15. Enter Master PIN Number on Keypad: ?? Enter temporary PIN Number: If the temporary PIN Number applies only to a certain Receiver, enter the PIN Number followed by the Receiver Identity (1-4). The result will be a five digit PIN Number (example: 12341). Temporary PIN Numbers “BEEP” “BEEP” The WKP5LM can support up to 5 PIN Numbers while the WKP250LM can support 250. Enter Master PIN Number on Keypad: ?? 9Enter new PIN Number: Adding PIN Numbers “BEEP” “BEEP” Enter Master PIN Number on Keypad: ?? 7Enter PIN number you want to remove: A triple beep indicates a PIN Number has been entered that does not exist. The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? Operation Enter existing Master PIN Number on Keypad: ???? 09### Enter new Master PIN Number: Change Master PIN Number “BEEP” “BEEP” To use Keypad, enter any valid PIN Number. With multiple Receivers, enter the PIN Number followed by the Receiver Identity (1-4). Pre-Installed Liftmaster Receiver Step 1: Pry open the front panel of the receiver case with a coin or a screwdriver. Step 2: Press and release the Learn button on the receiver. The Indicator Light will light for 30 seconds indicating that receiver is in Learn Mode. Step 3: Within 30 seconds enter Master PIN Number on Keypad. Step 4: Press “1”. Repeat Steps 2-4 for each remote, or control device that will be used to access the Liftmaster door or gate operator. Erase All Control Codes Press and hold the Learn button on the receiver until the Indicator Light turns off indicating that the receiver memory is clear (about 6 seconds). Indicator Light Learn Button A temporary PIN Number can be used only once within a 24 hour period. NOTE: The WKP5LM can hold up to 5 Temporary PIN Numbers while the WKP250LM can hold 15. Enter Master PIN Number on Keypad: ?? Enter temporary PIN Number: If the temporary PIN Number applies only to a certain Receiver, enter the PIN Number followed by the Receiver Identity (1-4). The result will be a five digit PIN Number (example: 12341). Temporary PIN Numbers “BEEP” “BEEP” The WKP5LM can support up to 5 PIN Numbers while the WKP250LM can support 250. Enter Master PIN Number on Keypad: ?? 9Enter new PIN Number: Adding PIN Numbers “BEEP” “BEEP” Enter Master PIN Number on Keypad: ?? 7Enter PIN number you want to remove: A triple beep indicates a PIN Number has been entered that does not exist. The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? 2 Mount Keypad Step 1 Choose mounting location for Keypad. Remove the back panel and attach it to a solid surface or post. Mount the Keypad onto the back panel with screws. Tighten screws with A...
Este manual também é adequado para os modelos :Vídeo - WKP250LM (128.07 kb)