Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time: Works: Day Night Test 5 Sec x x Auto 1, 5, 10 min. x Manual Until Dawn* x * resets to Auto Mode at dawn. Note: When first turned on wait about 1 1/2minutes for the circuitry to calibrate. TEST 10 5 1 TEST ON-TIMEPut the ON-TIME switch on the bottom of the sensor in the TEST position. AUTO ON-TIME 10 5 1 TEST Put the ON-TIME switch in the 1, 5, or 10 minute position. MANUAL MODE Manual mode only works at night because daylight returns the sensor to AUTO. Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position. 1 Second OFF then... ... back on. Mode Switching Summary TEST Move ON-TIME Switch to 1, 5, or 10 minutes AUTO Flip light switch off for one second then back on* MANUAL MODE * If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control will be in the AUTO mode. 240-029-A © 2003 Atlas Lighting Products, Inc. 598-1096-01 INSTALLATION For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. For eave mount only: . Swing the sensor head towards the clamp screw. Controls Clamp Screw . Rotate the sensor head clockwise 180° so the controls face down. Controls Controls If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done. These instructions show the sensor wired to flood- lamps. The white sensor wire is neutral. The black sensor wire is hot. The red wire is the switched "hot" wire. The lighting load (Up to 500 Watts, 4.2A Maximum) is placed across the white and red wires. WIRE THE LIGHT CONTROL. . After screwing the sensor into the wall plate, connect the junction box wires to the Light Control wires by twisting together and securing with wire connectors. Red Sensor Wire to MOUNT THE LIGHT. .Follow the instructions that came with your light fixture for mounting and adjusting the light fixture. .Keep regular PAR-38 lamps at least 1" (25 mm) from the sensor. Halogen lamps should be kept at least 2" (51 mm) from the sensor. Black to Black White to White Black Lamp Wire Optional:Connect additional load across the white and red wires. Total lighting load including lampheads on fixture must not exceed 500 Watts (4.2A). Junction Box Lamp Holders . Turn power off at the fuse or circuit breaker. . Remove the existing light fixture, if present. 598-1096-01 -2 TEST AND ADJUSTMENT . Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 1/2 minute calibration period before it will detect motion. When first turned on, wait 1 1/2 minutes. . Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. ON-TIME RANGE 10 5 1 TEST MIN MAX Bottom of Sensor Avoid aiming the control at: • Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering. • Areas wherepets or trafficmay trigger the control. • Nearby large, light-colored objects reflecting light may trigger the shut-off feature. Do not point other lights at the sensor. 8 ft. (2.4m) 70 ft. (21m) Maximum Range The sensor is less sensitive to motion directly towards it, most sensitive to motion across its field of view. Maximum 180° Coverage Angle Motion Sensor Least Sensitive Most Sensitive Motion . Loosen the clamp screw in Clamp the sensor ball joint and Screw gently rotate the sensor. . Walk through the cover- Ball age area noting where you Joint are when the lights turn on (also, the LED will flash several times when motion is detected). Move the sensor head up, down, or side-Aim Sensor ways to change the cover-Down for Short age area. Keep the sen-Coverage sor at least 1" (2.5 cm) away from the lamps. . Adjust the RANGE as needed. RANGE set too Aim Sensor high may increase false Higher for Long triggering. Coverage . Secure the sensor head by tightening the clamp screw. Do not overtighten the screw. . Set the amount of TIME you want the lights to stay on after motion is detected (1, 5, or 10 minutes). Warning - Risk of fire. Do not aim the lamps at ...
Este manual também é adequado para os modelos :Vídeo - GUARDIAN PRO MLGS180B (447.5 kb)