Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
Push the left side back so it rests against the step. 33 33 LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner. The slot on the right side of log #3 fits over the bar grate. 4444 LOG #4 (SRV349-704): Place the bottom left corner of log #4 behind log #2 and rest its top right corner on log #1. The bottom left corner of the log rests in the square cut out of the base pan. Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 55 55 55 55 LOG #5 (SRV327-705): Rest log #5 in the cutouts on both log #1 and log #3 as shown. The front edge of log #1 should be at the top of the hole when looking through the hole in log #5. 66 66 LOG #6 (SRV349-706): Position the "Y" end of log #6 into the cutout on log #4 and its opposite end into the groove on log #2. Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 If the gas logs have been factory installed they should not Log Set Assembly: LOGS-GXTneed to be positioned. If the logs have been packaged separately, refer to the following instructions. CAUTION: Logs are fragile! Carefully remove the logs from the packaging. 22 33 665544 11 PILOTPILOT BRACKETBRACKET BASEPANBASEPANBURNERBURNER GRATEGRATE 77 TABTAB TABTAB Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 11 11 LOG #1 (SRV339-701): Place log #1 in the back on the insert. Locate the left end of the log over the center of the pilot and the back side of the left end flush with the back of the pilot bracket. Pull the right end of the log forward until it touches the tab in the base pan. 22 22 LOG #2 (SRV339-702): Position log #2 by locating its slot over the tab on the front left of the burner. The slot in the left side of log #2 fits over the bar grate. 339-935 2/02 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 33 33 33 33 LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner. The slot in the right end of log #3 fits onto the bar grate. 44 44 LOG #4 (SRV339-704): Nest log #4 in the smooth cut-out areas on the left side of log #1 and place the left end on the base pan. Pull the left end forward until it touches the tab on the left side of the base pan. 55 55 LOG #5 (SRV438-724): Rest log #5 in the cutouts on both log #4 and log #2 as shown. The “Y” end of the log sits of log #4. The other end crosses log #2 and touches the center grate bar. Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 66 66 66 66 LOG #6 (SRV327-705): Rest log #6 in the smooth area just to the left of the knothole in log #1 and on log #3. The front edge of log #1 should be at the top of the hole when looking through the hole in log #6. 77 77 LOG #7 (SRV571-707): Rest log #7 in the smooth area just to the right of the knothole in log #1. The other end of log #7 rests on log #3 and slightly touches log #6. Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev. i • 12/09 27 Figure 11.5 Glass Assembly F. Glass Assembly G. Air Shutter Setting Optimal fl ame appearance is dependent on the air shutter setting. Adjustments should be made by a qualified technician. Handle glass doors with care. • Inspect the gasket to ensure it is undamaged. • Inspect the glass for cracks, chips or scratches. • Do NOT strike, slam or scratch glass. • Do NOT operate appliance with glass door removed, cracked, broken or scratched. • Replace glass door assembly as a complete appliance. WARNING Model NG LP Grand-XTS 1/2 in. Full Open (3/4 in.) Supreme-XTS 3/8 in. Full Open (3/4 in.) BOTTOM LATCH GLASS ASSEMBLY Removing Glass Assembly The glass assembly fastens to the fi replace in four places. Two or four of the fastening mechanisms will be springloaded glass latches, depending on the model. An example of the glass latch is shown in Figure 11.5. Supreme-XTS To release glass assembly, pull the two bottom springloaded latches forward and allow them to retract away from the glass assembly. Remove glass assembly by carefully pulling the bottom side of the glass assembly out fi rst. Carefully slide the glass assembly outward and downward until the top tabs are disengaged from the slots. Grand-XTS To release glass assembly, pull the two bottom springloaded latches forward and allow them to retract away from the glass assembly. Slide the glass assembly outward and downward until the top latches disengage. Replacing Glass Assembly Supreme-XTS Tilt glass assembly toward fireplace and slide glass assembly up to engage top two tabs with the corresponding slots. Fasten the two bottom latches. Grand-XTS Tilt glass assembly toward fi replace and slide glass assembly upward to engage top latches. Verify top latches are fully engaged and then fasten the two bottom latches. 112 Operating Instructions A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before operating this appliance have a qualified technician: • Remove all shipping materials from insid...
Este manual também é adequado para os modelos :Aquecedores de Água - SUPREME-XTS (3.15 mb)