Assessments - , GPA:
(
)
)
Fabricante : Desa
Arquivo Tamanho: 304.62 kb
Arquivo Nome : 8635f8a4-23e5-4575-a198-935b85b76cf2.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
WARNING: HOTTER WATER INCREASES THE RISK OF SCALD 3. Depress gas control slightly and turn clock-wise to “OFF”. If knob is in “ON” position, turn clock-wise to “PILOT” then depress knob slightly and turn clock-wise to “OFF”. 4. Wait five (5) minutes to clear out any gas. If you smell gas, STOP! Follow “B” in the safety information at the head of this section. If you don’t smell gas, go to the next step. 5. Remove burner access cover located below the gas control unit. 6. Find pilot - follow small metal tubes from gas control. The pilot is located between the two centre burners. 7. Turn knob on gas control knob counter-clock-wise to “PILOT” 8. Depress control knob all the way and hold in. Immediately light the pilot with a match. Continue to hold the control knob down for about 1 minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 3,4,7 and 8. If knob does not pop up when released, turn clock-wise to “OFF”, stop and immediately call your service technician or gas supplier. If the pilot will not stay lit after several tries, turn the gas control knob “OFF” and call your service technician or gas supplier. 9. Replace burner access cover. 10.Turn gas control knob counter-clock-wise to “ON” position. Set the thermostat to desired setting clock-wise. BEFORE LIGHTING, SNIFF AT FLOOR LEVEL. IF YOU SMELL GAS, FOLLOW THESE RULES: 1. Get all people out of the building. 2. DO NOT light matches. 3. DO NOT TOUCH electrical switches (on or off) 4. DO NOT use an electric fan to remove gas from area. 5. SHUT OFF GAS at the LP tank outside of the building. 6. IMMEDIATELY call the LP Gas Company or the fire department from a neighbour’s telephone. Ask for instructions, before hanging up, give your name, address and telephone number. 7. DO NOT go back into the building. If help is coming, wait for it outside of the building. Page 12 LIGHTING INSTRUCTIONS FOR ELECTRONIC IGNITION GAS MODELS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance is equipped with an ignition device which automatically lights the pilot, DO NOT TRY TO LIGHT MANUALLY. B. BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. What Do You Do If You Smell Gas? - Do not try to light any appliance. -Do not touch any electrical switch: do not use any phone in the building. -Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions. -If you cannot reach your gas supplier, call the fire department. C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, don’t try to repair it, call a qualified service technician. Forcing or attempting to repair may result in fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system, and any gas control which has been under water. Operating Instructions 1. Stop! Read the safety information above. 2. Turn off all electric power to appliance. 3. Remove thermostat access door. 4. Set thermostat to lowest setting. 5. This appliance is equipped with an ignition device which automatically lights the pilot. DO NOT TRY TO LIGHT THE PILOT MANUALLY. 6. Turn gas control know clock-wise to “OFF” 7. Wait (5) five minutes to clear out any gas. If you then smell gas, STOP. Follow section “B” in the safety information at the head of this section. If you don’t smell gas, go to next steps. 8. Turn gas control knob counter-clock-wise to “ON” 9. Set thermostat to desired setting. 10. Replace insulation and thermostat access door. 11. Turn on all electric power to the appliance. 12. If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO THE APPLIANCE”, and call your service technician or gas supplier. GAS INLET GAS CONTROL KNOB (IN OFF POSITION IGNITES CONNECTION PILOT TUBE GAS OUTLET CONNECTION To Turn Off Gas To Appliance 1. Turn off all power to appliance. 2. Remove thermostat access door. 3. Set the thermostat to lowest setting. 4. Turn gas control knob clock-wise to “OFF”. Do not force. 5. Replace control access panel. Page 13 COMMERCIAL GAS E.I. TROUBLESHOOTING SEQUENCE For Honeywell Valve NOTE: Troubleshooting should be done by qualified service personnel familiar with the start-up and checkout procedure. TURN GAS SUPPLY OFF SET THERMOSTAT TO CALL FOR HEAT VALVE IS POWERED (24 VAC NOMINAL) IS FLUE DAMPER POWERED ACROSS TERMINALS 3 & 7 IGNITES WARMS UP AND GLOWS RED PILOT VALVE OPENS TURN GAS ON, PILOT BURNER LIGHTS? MAIN VALVE OPENS? SYSTEM ON CHECK -LINE VOLTAGE POWER -LOW VOLTAGE TRANSFORMER -AQUASTAT (E.C.O.) -WIRING CHECK -SWITCH CONTACT SS OR ES NOT MADE -DAMPER FU...
Este manual também é adequado para os modelos :Aquecedores de Água - G65 (304.62 kb)