21 Logs Parts List & Parts View ....................................................................................................................... 22 Service Notes................................................................................................................................................ 23 Installer: Please leave these instructions with the consumer. Consumer: Please retain these instructions for future use. 12409-2-0403 Page 2 IMPORTANT SAFETY INFORMATION IMPORTANT SAFE

3. The right, middle log (#3) will go directly on the two pins on the right side of the flat portion of the main burner. 4. The left, middle log (#4) should be placed flat on the pin on the left side of the flat portion of the main burner. The left, 2 1 Log Placement VFYR and VFYM -(18, 24, 30)SO Logs Shown Figure 13 middle log will rest on a pin located on the right, middle log. 3 4 RWO Curing Process The logs shipped with this product are formed from a cast refractory material. The curing proc

11 West 42nd St. Batterymarch Park New York, NY 10018 Quincy, MA 02269 12409-2-0403 Page 7 CLEARANCES CLEARANCES Minimum Dimensions For Solid Fuel Burning Fireplaces UL127 Factory Built Fireplaces (Figure 2) Model ABCD VFYM-16 18" 13" 24" 18" VFYR-16 18" 13" 24" 18" VFYM-18 17" 14" 28" 17" VFYR-18 17" 14" 28" 17" VFYM-24 23" 14" 30" 18" VFYR-24 23" 14" 30" 18" VFYM-30 26" 14" 34" 20" VFYR-30 26" 14" 34" 20" Figure 2 The dimensions shown and defined in the fireplace manufacturer’s instructions ar

d. Ignitor cable pinched or wet. Keep ignitor cable dry - Free ignitor cable if pinched by any metal or tubing. e. Broken ignitor cable - Replace ignitor cable. f. Bad piezo ignitor - Replace piezo ignitor. 2. Appliance produces unwanted odors. a. Appliance burning vapors from paint, hair spray, glues, etc. -Ventilate room. Stop using odor causing products while heater is running. b. Gas leak - Locate and correct all leaks. 3. Appliance shuts off during use. (Pilot and main burner are off.) a. N

12. No gas to pilot. a. LP-regulator shut down due to inlet pressure too high Verify LP tank regulator is installed and set at 11" to 13" w.c. Replace regulator on heater. If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the gas quality orpressure is low, contact your local gas supplier immediately. HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or dealer. For best results, the service p

If the manual gas control knob is in mid-position, between heat settings, incomplete combustion will take place, causing odor, and may produce gas leakage or carbon monoxide. 10. Turn on all electric power to appliance (if applicable). TO TURN OFF GAS TO APPLIANCE 1. Turn off all electric power to appliance if service is to be performed (if applicable). 2. Push in manual gas control knob slightly and turn clockwise to "OFF". Do not force. PILOT FLAME CHARACTERISTICS The correct flame will be blu

USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. SR-10 PARTS VIEW SR-30 PARTS VIEW OPTIONAL BLOWER INSTALLATION INSTRUCTIONS (continued) Wiring The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, if an external electrical source is utilized. This appliance is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged direc

43 Maintenance and Service............................................................................................................. 44 Parts View...................................................................................................................................... 45 Parts List ....................................................................................................................................... 46 FBB4 Optional Variable Speed Blower Installation ..............

To prevent triggering of smoke alarms, ventilate the room in which the unit is installed. IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this manual for future reference. Please read this manual before installing and using the appliance. WARNING: Any modification to this unvented gas heater or its controls can be dangerous. Improper installation or use

(2.615kPa). Propane/LP gas will have a manifold pressure approximately 10.0" w.c. (2.49kPa) at the pressure regulator outlet with the inlet pressure to the pressure regulator from a minimum of 11.0" w.c. (2.739kPa) for the purpose of input adjustment to a maximum of 13.0" w.c. (3.237kPa). A test gage connection is located downstream of the gas appliance pressure regulator for measuring gas pressure. The connection is a 1/8 inch (3mm) N.P.T. plugged tapping. Recommended Gas Pipe Diameter Pipe Len