Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Do not allow the softener's weight to rest on the inlet and outlet fittings or they will break. 8. Tip the bottom of the softener up a few inches and hold until all water has drained. Leave the softener laying like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, bugs, etc. out. 18 SECTION 3 OFYOUR CARESOFTENER 3D. HELPFUL HINTS CHECKLIST ... TO HELP YOU SAVE MONEY If your water softener fails to work, make the following easy checks. Often, you will find what's wrong yourself and you won't have to call and wait for service. If you do not find anything wrong, while making the checks, and your softener still does not work, call your Sears Service Department. NOTES: 1. Also read ERROR CODE, page 12. 2. If an error code is not displayed, press and bold the #1 SELECT button until the display changes. Then, press the #1 SELECT button again and bold until a flashing HF code appears. It must show I-IF32. If any other number shows, the face plate computer is working on incorrect input and would probably be the cause of the problem. To set ITF32, press either the UP I_ or DOWN _ button. When HF32 shows, press #1 SELECT button to return a flashing 12:00 AM display. Reset the present time, hardness number, etc., pages 6 and 7. PROBLEM CAUSE CORRECTION No soft water Nosalt(orsaltbridged)inthestoragetank Refillwithsalt,orbreakthesaltbridge(page 16). Press ON/OFF-HOLD (RECHARGE NOW) buttonand holdfor 3 seconds to start a regeneration (see page 10). Transfomer unplugged at the wall outlet, Check for loss of power due to any of these or power cable leads loose, fuse blown, and correct. With the power back on, look at circuit breaker popped, or circuitswitched the time display and read PROGRAM off. MEMORY, page 12. Manual bypass valve(s) in bypass position Look at FIG. t2 on page 20. Move the stem in a single valve to service. In a 3-valve bypass, open the inlet and outlet valves, and be sureto fully close the bypass valve. Dirty, plugged or damaged nozzle & Take apart and clean or replace damaged venturi parts (see page 17). Valve drain hose plugged The drain hose must not have kinks, sharp bends, or be raised too high above the softener (see page 16 in your installation manual. Water hard sometimes Hardness number setting too low Press and release the #1 SELECT button untU HARDNESS shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown on your water analysis report. See page 7 to reset. Press and release the SELECT button until the present time shows in the display. Using hot water when softener is Avoid usinghotwaterduringthistimebecause regenerating the water heater refills with hard water (see Automatic Bypass, page 15). Increase inthegrainsofhardnessinyour AskyourSearsretailorcatalogstoreforanew water supply water analysis. Then make a new hardness number setting (page 7). 19 SECTION 4 THINQS OTHERTOK.OW 4A. DIMENSIONS/SPECIFICATIONS BYPASS VALVES SINGLE PULL OUT / \ forservice I I I I I -I IN for bypass E C A 3 -VALVE Bypass Valve close bypass valve open inlet & outlet valves Outlet INCHES CM FOR BYPASS bInlet Valve A Salt Tank Height 40-1/4 102.2 open bypass valve close inlet & outlet valves B C Resin Tank Diameter (nominal) Resin Tank Height (nominal) 9 40 22.7 101.6 D Inlet-Outlet Height 41-1/2 105.4 E Overall Height 47 119.4 F1 Length 19-1/2 49.5 F2 Width 16-1/2 41.9 -Distance between inlet-outlet 3-7/8 9.8 center lines MODEL NO. 625.348670 TIMER HF CODE HF32 NOTE: Please see the rating decal for water softener operating capacity, salt usage and service flow rate/pressure loss performance specifications. Performance specifications are validated by the Water Quality Association (WQA). The rating decal is located on the rim, under the salt hole cover (see page 30). WATER SUPPLY TO WATER SOFTENER MINIMUM WATERSYSTEM FLOW (gpm) ................ 3 TYPE OF ION EXCHANGE MATERIAL (resin) High Capacity MINIMUM-MAXIMUM WATERPRESSURE (psi) ..... 20-120 AMOUNT OF RESIN (cu.ft.) .......................... 1.0 MAXIMUM WATERTEMPERATURE (°F) ............... 120 REGENERATION (RECHARGE) CYCLE TIME (min.) MAXIMUM WATERHARDNESS (gpg) ................. 110 FILL (NaCL setting) ........................... 2.7-10.6 MAXMUM "CLEARWATER"IRON (ppm) ................. 6 FILL (KCI setting) ............................. 3.8-12.6 BRINING / BR. RINSE ........................ 120-135 BACKWASH ....................................... 7 SALT FOR WATER SOFTENER FAST RINSE ....................................... 3 TYPE OF SALT NEEDED ................... Nugget/Pellet TOTAL REGENERATION TIME ............ 139.4--164.4 ALTERNATETYPE OF SALT .. Pure,evaporated,compacted water softenersalt gpm = gallons per minute psi = pounds per square inch STORAGE CAPACITY(pounds)....................... 200 gpg = grains per gallon ppm = parts per million 20 SECTION 5 SERVICE TECH INFORMATION 5A. TROUBLESHOOTING Keep this manual with your water softener. If repairs are needed...