. . This composite filter has the function to improve water taste and reduce aesthetic chlorine. 21 The Hydrogen Ion Concentration (pH) measuring cycle and precautions. Immediately after installing this device, measure the Hydrogen Ion Concentration (pH) after extracting string ionized alkaline water for at least 4 minutes. Please check the Hydrogen Ion Concentration (pH) of the ionized water at least once a month. Tips Measuring the hydrogen ion Concentration (pH) 1. Extract weak ionized alkali

........................................................ .................................. ................................ .................... ................................................ ...................... ...................... ........................................................ .................................. ................................ .................... ................................................ ...................... ...................... ..................

Clean after unplugging, and don’t clean by spraying the water directly or don’t wipe the product using the benzene and thinner. Otherwise, electric shock or fire may occur as a result. Do not move the product by pulling the power cord. (P-07QR only) Otherwise, electric shock or fire may occur as a result. 3 3 SAFETY INFORMATION Warning: If not observed, serious physical injury or property damage may occur as a result. Caution: If not observed, minor physical injury or property damage may occur a

(Based on the tap water) Therefore, the filter change cycle may be reduced for the area with poor water quality or more applications. Filter Replacement Cycle Filter Replacement Method 2. Please separate the top cover and the front cover. (After blocking the main water extraction hole using the faucet stopper in the top of the inner water tank and loosing a screw with a driver, separate it.) . . . 1. After pulling the power cord necessarily (P-07QR only), close the main water supply valve and dr

This item is available in all modes. -67 to 149°F (-55 to 65°C) BOB. sup j Lj g* occ • Boiler Supply - Current boiler supply water temperature as measured by the boiler supply sensor. This item is available in all modes. 14 to 266°F (-10 to 130°C) BOB. ir r T TAflQ 1 J J OCC D1 E1 F1 • Boiler Target - Boiler target temperature is the temperature the control is currently trying to maintain at the boiler supply sensor +/-1/2 of the differential. This item is available in all modes. —, 14

A large easy to read display provides current system temperatures and operating status (FIG. 1). The control has outputs for a primary pump and a combustion air damper or alarm. Based on the mode of operation selected, the control can operate different combinations of boiler stages and boiler pumps. ADDITIONAL FUNCTIONS INCLUDE: • Installer and Advanced Access Levels • Primary Pump Output • Individual Boiler Pump Outputs (in applicable modes) • Pump Exercising • Pump Purging (primary and b

This is typical of many commercial cast iron and steel tube boilers. The HI MASS setting stages on additional boilers at the slowest rate. Differential An on / off heat source must be operated with a differential to prevent short cycling. With the control, either a fixed or an auto differential may be selected. The boiler differential is divided around the boiler target temperature. The first stage contact closes when the supply water temperature is % of the differential setting below the boil

An external signal is generated by applying a voltage between 0 v (dc) and 10 v (dc) across the out + and Com - terminals (4 and 1) (FIG. 25). Once voltage is applied, the External Input Signal pointer is displayed in the LCD and the control closes the primary pump contact. The control calculates a boiler target supply temperature based on the external input signal and the settings made in the control. The control then fires the boiler(s), if required, to maintain the target supply temperature.

* Place a Taste & Odor Filter UPSTREAM of a water softener on a chlorinated water supply FIG. 2 and DOWNSTREAM of a water softener on a non-chlorinated water supply. Questions? Call The Kenmore Water Line 1-800-426-9345 Typical WHERE TO INSTALL THE WATER SOFTENER Review the following points before you choose a place 1. Place as close as possible but always after, the pressure tank (well water) or water meter (city water). See Fig. 3. 2. Place as close as possible to a water drain such as a floor

• Warranty card is included in this User’s Manual. 1 FEATURES 1. Continuous extraction function If you let the coke lever down, as you can extract the water continuously in a state of stopped lever, it is convenient. 2. Uniform water pressure keeping function In the area with the high water pressure, it protects the inside of the product from the high water pressure by providing a main water with an uniformed water pressure. 3. Closed tank for preventing the secondary pollution It is the hygieni