Log:
Assessments - 5, GPA: 4.2 ( )

Instruções de Operação Briggs & Stratton, Modelo 310700

Fabricante : Briggs & Stratton
Arquivo Tamanho: 477.38 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


(Whenever possible, gradually reduce engine speed before stopping.) DO NOT tamper with governor springs, links or other parts to increase engine speed. (Run engine at speed set for equipment manufacturer.) DO NOT check for spark with spark plug removed. (Use an approved tester.) DO NOT crank engine with spark plug removed. (If engine is flooded, place throttle in FAST and crank until engine starts.) DO NOT strike flywheel with a hammer or hard object as this may cause flywheel to shatter in operation. (To remove flywheel, use Briggs & Stratton approved tools only.) DO NOT operate engine without a muffler. (Inspect periodically and replace if worn or leaking. If engine is equipped with muf- fler deflector, inspect periodically and replace if necessary. Re- placement parts must be same as on original equipment.) DO NOT operate engine with an accumulation of grass, leaves or other combustible material in muffler area. DO NOT use this engine on any forest covered, brush cov- ered, or grass covered unimproved land unless a spark ar- rester is installed on muffler. The spark arrester must be main- tained in working order by the owner and/or operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. DO NOT touch hot muffler, cylinder, or fins which can cause burns. DO NOT start engine with air cleaner or air cleaner cover re- moved (or cover over carburetor air intake, if Sno/Gard engine). DO NOT attempt to start engine with cutting blade loose or re- moved. (Blade must be tight, otherwise a kickback may occur.) 4 PULL starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury. 4 PREVENT ACCIDENTAL STARTING by removing spark plug wire from spark plug when servicing engine or equip- ment. Disconnect negative wire from battery terminal if equipped with electric starting system. 4 REMOVE blower housing periodically and clean engine. Keep cylinder fins and governor parts free of dirt, grass and other debris which can affect engine speed. 4 USE fresh gasoline. Stale fuel can gum carburetor and cause leakage. 4 CHECK fuel lines and fittings frequently for cracks or leaks. Replace if necessary. 4 Use only Genuine Briggs & Stratton Parts or their equivalent. The use of replacement parts which are not of equivalent quality may damage the engine. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Safety Alert - Read Owner’s Manual International Symbols FuelOn Off Stop ChokeFuel Shutoff In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 2 In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 3 Oil & Fuel Recommendations Oil This engine is shipped from Briggs & Stratton without oil. Before starting engine, check oil level as shown below. Change and add oil according to chart below. Do not over-fill. Use a high quality detergent oil classified “For Service SF, SG, SH,” such as Briggs & Stratton “warranty certified” SAE 30 oil, Part No. 100005. Use no special additives with recommended oils. Do not mix oil with gasoline. SAE Viscosity Grades °C -30 STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE °F -20 0 20 40 60 80 100 -20 -10 0 10 20 30 40 * ** 32 * Air cooled engines run hotter than automotive engines. The use of multi-viscosity oil such as (10W-30, etc.) in ambient temperatures above 40° F (4° C) will result in higher than normal oil consumption. If multi-viscosity oil is used, check the oil level more frequently to prevent any possible engine damage due to lack of lubrication. ** Use of SAE 30 oil below 40° F (4° C) will result in hard starting and possible engine damage due to inadequate lubrication. Fuel Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. Fresh fuel prevents gum from forming in fuel system or on essential carburetor parts. Purchase fuel in quantity that can be used within 30 days. In countries other than the U.S.A., leaded gasoline may be used if commercially available and unleaded is unavailable. We recommend the use o...

Este manual também é adequado para os modelos :
Air - 28N700 (477.38 kb)
Air - 311700 (477.38 kb)
Air - 312700 (477.38 kb)
Air - 313700 (477.38 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias