2 24 Your new appliance Control panel pure air evolution 0 30° °C 20° Control knob Full water tank Thermostat Air outlet grille indicator light 0 Appliance off Maximum air conditioning Silent air conditioning Dehumidification Air purification Heating Fig. 3 Fig. 5 Model PA18100M 0 Appliance off Maximum air conditioning Silent air conditioning Dehumidification Silent air purification Maximum air purification Fig. 4 Model PA19000M Your new appliance Description of accessories Suction pad Base filter Purifying Filter Double active filter Art. Nr.: PA10000Z Wall grommet window Art. Nr.: PA11000Z Sliding balcony accessory Art. Nr.: 475075 PA19000M • • * PA18100M • • * Approx. measurement min / max (length x width) cm. o wall 10,5 70x10/ 205x10 Standard accessories: These accessories are supplied with the appliance. • Optional accessories: These accessories are available for purchase from the manufacturer's official technical service and authorised distributors. * * Optional accessories: These accessories are only available for purchase from the manufacturer's official technical service. Requirements for use Condiciones de utilizacion . For safety reasons, the appliance must be at least 20 cm away from any nearby . This home appliance should be connected surface before it is turned on. Fig. 6. to a 220/240 V, 50 Hz mains electricity supply via an earthed socket. . It must be protected with a 10 A slow-action fuse. . Should an extension lead be required, then this lead should be at least 1.5 mm2 thick per terminal, less than 25 m long and earthed. . There is a cavity at the back of the appliance to house the mains electricity supply cable. See Fig. 2. . Do not allow water to enter your appliance and do not cover the air intakes/outlets. min. 20 cm. min. 20 cm. Fig. 6 Warning! The mains electricity supply connection cable must only be replaced by authorised members of the manufacturer ’s Official Technical Service. 25 26 Requirements for use When the appliance is turned off and then turned back on, it takes the compressor 3 minutes to start up again. This period of time is required in order to ensure correct operation. Avoid direct contact with the air expelled through the expulsion tube. Transportation requirements The appliance is fitted with wheels to make it easier to move around. If necessary, you can tilt the appliance in order to move it. You should not turn the appliance back on again for a minimum period of one hour after performing this procedure. . Before tilting it, empty the condensed water from the internal tank by extracting the water drainage pipe from its housing and removing the plug, Fig. 7. Do not forget to replace the plug and reinsert the pipe in its housing when the tank is empty. Instructions for Use Cooling The appliance cools and dehumidifies the air in the room at the same time in order to create a pleasant atmosphere. . Plug the appliance into the mains electricity supply. . Lead the hot air expulsion tube outside. In order to avoid excessive noise and efficiency loss, the air expulsion tube should be positioned as shown in Fig. 14. See "Ways of releasing air outdoors". . Check that the plug, Fig. 1, is fitted on the drainage pipe to prevent water from leaking onto the support surface. . Lift the air director on the top of the appliance. This air director is not installed on the appliance on PA18100M models. See figures 25 and 26 in "Heating". . Select the maximum or silent cooling function, Fig. 8. (The silent cooling function reduces the air flow on the appliance). . Set the thermostat to the desired temperature. Fig. 9. If the appliance turns itself off automatically because the thermostat trips, it is necessary to wait for ambient temperature to rise 2-3°C before it comes back on again. Fig. 7 0 Fig. 8 30 ° °C 20° Fig. 9 In order to fit the expulsion tube assembly properly in its housing, it is necessary to slide the sleeve into the positioning slot (as shown by the arrows on Fig. 12). The diffusion duct, Fig. 10, is added when the tube assembly has been fitted onto the appliance. Press the "Push" tab (Fig. 13, 1) and slide out (Fig, 13, 2) to remove the assembly from the appliance. Temporary installation . Open the window slightly and position the diffusion duct between the jamb and the glaze frame. . Close the window as far as possible and secure it with the suction pad supplied, Fig. 14. Fig. 12 Fig. 13 Fig. 14 27 Instructions for Use During air conditioning, some of the condensed water produced evaporates automatically and is expelled outdoors together with the expelled air through the hot air expulsion tube. In conditions of extreme humidity, the appliance accumulates condensed water in an internal tank. When a certain level is reached an indicator light, Fig. 3, comes on indicating that the condensed water tank is full and needs to be emptied. When this happens, the appliance stops cooling the air in the room until the water is drained, as explained in "Transportation requireme...

Este manual também é adequado para os modelos :
Air - PA19000M/01 (9.73 mb)
Air - PA19000M/02 (9.73 mb)
Air - PA19000M/03 (9.73 mb)