Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
AUTO operation The fan speed is automati- cally switched (HIGH, LOW, SILENT) depending on the amount of odor in the air. The sensor detects the odor for efficient air purification. SILENT operation The unit will operate quietly using minimal air intake. Stop POLLEN mode operation The unit will operate at High fan speed for 10 minutes, then will al- ternate between LOW and HIGH. 10 minutes: High fan speed 20 minutes: Low fan speed 20 minutes: High fan speed QUICK AUTO operation The unit will operate at High fan speed for 10 minutes, then will operate in AUTO operation. LOW operation HIGH operation 10 minutes: High fan speed AUTO operation OPERATION OPERATION ENGLISH REMOTE CONTROL USE • Operate with the remote control facing the main unit receiver. • The signal range is about 23 feet (7m). •Make sure there are no objects blocking the path of the signal. •A beep sound will be heard from the main unit when a signal is received. NOTE •Avoid dropping or damaging the remote control, using in a high humidity condition, in direct sunlight or near a heat source. Receiver Transmitter E-13 Plasmacluster AUTO MANUAL Fan Control POLLEN OFF TIMER QUICK AUTO POWER ON/OFF CLEAN ION CONTROL OFFAUTO Plasmacluster Ion mode Selections Auto When pressed, the unit will switch between Clean Mode and the Ion Control Mode auto- matically depending on the amount of impuri- ties in the air as detected by the odor sensor. Clean Mode will operate for 1 minute when the Auto function is selected. Ion Control When pressed, the unit will constantly oper- ate in Ion Control Mode. The Plasmacluster Ion Indicator Light is green. Clean When pressed, the unit will con- stantly operate in the Clean Mode, in which the same numbers of posi- tive and negative ions are dis- charged. The Plasmacluster Indica- tor Light is blue. Off The generation of ions will cease and the Plasmacluster Indicator Light will go out. REMOTE CONTROL OPERATION OPERATION Operations available withthe Remote Control • AUTO • MANUAL • POLLEN • OFF TIMER • QUICK AUTO Plasmacluster Ion mode selections • AUTO • CLEAN • ION CONTROL • OFF •When you press the POWER ON/OFF Button, a short beep will sound and operation will start in AUTO Mode. Transmitter Pollen Mode Operation Button See Page E-12 Off Timer Button The set time switches every time the button is pressed as shown below. 1 hour 4 hours Cancel 8 hours • The indicator light shows the remaining time. POWER ON/OFF Button To stop, press the POWER ON/OFF Button again. A long beep will sound and operation will stop. Auto (Fan Speed) Button The fan speed switches au- tomatically depending on the amount of impurities in the air. Manual (Fan Speed) Button The fan speed can be switched among Silent, Low, and High settings. Quick Auto Button The operation mode is effec- tive when quick removal of impurities in the air is de- sired. Note: By manually selecting ei- ther Ion Control or Clean Mode, this will lock the unit into the selected mode and will not change to the other even if room condition changes. Plasmacluster AUTO MANUAL Fan Control POLLEN OFF TIMER QUICK AUTO POWER ON/OFF CLEAN ION CONTROL OFFAUTO Plasmacluster Ion mode Selections Auto When pressed, the unit will switch between Clean Mode and the Ion Control Mode auto- matically depending on the amount of impuri- ties in the air as detected by the odor sensor. Clean Mode will operate for 1 minute when the Auto function is selected. Ion Control When pressed, the unit will constantly oper- ate in Ion Control Mode. The Plasmacluster Ion Indicator Light is green. Clean When pressed, the unit will con- stantly operate in the Clean Mode, in which the same numbers of posi- tive and negative ions are dis- charged. The Plasmacluster Indica- tor Light is blue. Off The generation of ions will cease and the Plasmacluster Indicator Light will go out. REMOTE CONTROL OPERATION OPERATION Operations available withthe Remote Control • AUTO • MANUAL • POLLEN • OFF TIMER • QUICK AUTO Plasmacluster Ion mode selections • AUTO • CLEAN • ION CONTROL • OFF •When you press the POWER ON/OFF Button, a short beep will sound and operation will start in AUTO Mode. Transmitter Pollen Mode Operation Button See Page E-12 Off Timer Button The set time switches every time the button is pressed as shown below. 1 hour 4 hours Cancel 8 hours • The indicator light shows the remaining time. POWER ON/OFF Button To stop, press the POWER ON/OFF Button again. A long beep will sound and operation will stop. Auto (Fan Speed) Button The fan speed switches au- tomatically depending on the amount of impurities in the air. Manual (Fan Speed) Button The fan speed can be switched among Silent, Low, and High settings. Quick Auto Button The operation mode is effec- tive when quick removal of impurities in the air is de- sired. Note: By manually selecting ei- ther Ion Control or Clean Mode, this will lock the unit into the selected mode and will not change to the other even if room condition changes. 4 CARE AND MAINTENANCE CAR...