Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
national building regulations). - The ducting system for this appliance must not be connected to any ventilation system which is being used for any other purpose. - The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. - Do not leave naked flames or carry out flambè cooking under this cooker hood. - This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. CONNECTING THE POWER CABLE TO THE MAINS POWER SUPPLY Before installation, check that the mains voltage indicated on the rating plate inside the appliance corresponds to the voltage available in your home. If the Hood is not fitted with a plug, fit the power cable with a plug of a type approved for the load indicated on the rating plate; when connecting directly to the mains, insert an omnipolar circuit breaker with a minimum contact aperture of 3mm and a size suitable for the load in question between the appliance and the mains supply, making sure it is of a type that complies with current regulations. COMPONENTS C L - 2 No Wall Brackets C - 1 No 150-120mm Ducting Spigot G - 1 No Air Outlet Connection H (Optional) - 2 No Charcoal Filters L (Optional) m—o EN 9 INSTALLATION The cooker hood must be installed centrally over a cooking appliance. The minimum distance between the cooking surface and the metal grease filters on the underside of the hood must be at least 650mm. To install the hood proceed as follows: 1) Drill six 8mm diameter holes at X1-X2-J and insert the plastic rawl plugs supplied as illustrated in fig. 2 ensuring the brackets are fitted as shown in the blow up. 2) Secure the two brackets C to the wall inserting two of the screws supplied through the two holes on line X1-X2 as illustrated in fig. 2. 3) Slide the canopy down the wall to locate the key hole over the washer then secure the canopy to the wall by inserting two of the screws supplied through the two outer holes in the rim of the canopy J1 and J2 as illustrated in fig. 3. 4) EXTRACTION OR RECIRCULATION INSTALLATION: • EXTRACTION (DUCTED) When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 0 150 or 120 mm, the choice of which is left to the installer. • To install a 0 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. • Fix the pipe in position using sufficient pipe clamps (not supplied). • Remove any activated charcoal filters. • RECIRCULATION (FILTERED) • When the hood is fitted in the recirculation mode the Air Outlet Connection H should be fitted as illustrated in fig. 6. • Fit the (optional) charcoal filters by repeating the following operation on each side of the motor housing. Place the two key hole slots in the filter L and turn the filter clockwise to lock the filter in position as illustrated in fig. 7. WARNING: It is a possible fire hazard if the metal grease filters are not cleaned and the charcoal filters replaced regularly. Fitting The Chimney 5) FITTING THE CHIMNEY UPPER To fit the upper chimney A, place the top edge of the chimney over the bracket C as illustrated in fig. 8 and secure the chimney using two of the 2.9mm self tapping screws provided. The distance H in the height between the fixing holes X1 and X2 is determined by the height of the upper chimney A. 6) FITTING THE CHIMNEY LOWER To fit the lower chimney B, apply slight force to the two rear edges to increase the width of the apperture, then sleeve the chimney B over the chimney A as illustrated in fig. 9. EN 10 USE - MAINTENANCE USE The cooker hood functions are controlled by a series of slider or push button switches mounted on the front of the hood and control the worktop lighting and fan motor speeds. This cooker hood will not remove steam. 1) SLIDER SWITCHES (fig.11): - A switch controls the wotktop lighting - ON/OFF. - A switch controls the fan speeds - OFF/ON-1-2-3. - The red neon lamp illuminates when the motor is switched ON . MAINTENANC...
Este manual também é adequado para os modelos :Hoods - ZHC9141 (546.7 kb)
Hoods - ZHC6141 (546.7 kb)