Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
If installing a ventilation system in a room with a heat- producing appliance connected to a chimney/flue, the electricity supply to the hood must be equipped with a suitable safety switch. Risk of fire! Grease deposits in the grease filter may catch fire. The specified safety distances must be observed in order to prevent an accumulation of heat. Observe the specifications for your cooking appliance. If gas and electric hobs are operated together, the largest specified distance applies. Only one side of the appliance may be installed directly next to a high- sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm. Risk of injury! ¦ Components inside the appliance may have sharp edges. Wear protective gloves. ¦ The appliance may fall from the wall if it is not attached properly. All fastening components must be fixed firmly and securely in place. ¦ The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment. Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. Danger of suffocation! Packaging material is dangerous to children. Never allow children to play with packaging material. General information Exhaust air mode Note: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heat-producing appliances. ¦ Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible. ¦ If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. Exhaust duct Note: The appliance manufacturer does not assume any warranty for complaints attributable to the pipe section. ¦ The appliance achieves its optimum performance by means of a short, straight exhaust air pipe and as large a pipe diameter as possible. ¦ Because of long rough exhaust air pipes, many of which are pipe bends or have diameters smaller than 150 mm, the optimum extraction performance is not achieved and fan noise is increased. ¦ The pipes or hoses for laying the exhaust duct must consist of non-combustible material. Round pipes An inner diameter of 150 mm, but at least 120 mm, is recommended. Flat ducts The inner cross- section must correspond to the diameter of the round pipes. O 150 mm approx. 177 cm2 O 120 mm approx. 113 cm2 ¦ Flat ducts should have no sharp deflections. ¦ Use sealing strip for deviating pipe diameters. 20 Checking the wall ¦ The wall must be level, vertical and adequately load-bearing. ¦ The depth of the bore holes must be the same length as the screws. The wall plugs must have a secure grip. ¦ The enclosed screws and wall plugs are suitable for solid brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks). ¦ The max. weight of the extractor hood is 40 kg. Electrical connection : Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal mesh grease filter. Length of the cable: approx. 1.30 m This appliance complies with the EC interference suppression regulations. This appliance may be connected to a correctly installed earthed socket only. Attach the earthed socket preferably inside the flue duct. ¦ The earthed socket should be connected via its own circuit. ¦ If the earthed socket is no longer accessible following installation of the appliance, a disconnecter must be fitted as for a permanent connection. If a permanent connection is required, the installation must feature an all-pole disconnecter (circuit breakers, fuses and contactors) with a min. 3 mm contact opening. The permanent connection may be installed by an electrician only. Installation Preparing for installation Caution! Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made. 1.Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood. 2.Mark the positions for the screws and the contour of the attachment area. 3.Drill 8 mm O holes to a depth of 80 mm and press the wall plugs flush with the wall. . 4.Screw on the fixing bracket for the flue duct. © 5.Screw in 2 securing screws with washers to approx. 5 mm. . Installation 1.Attaching and aligning the appliance. . 2.Mark the hole for the safety screw. © 3.Remove the appliance once more. . F i n i s h in g in stall a tio n o f t h e a p p lian c e 1. Drill an 8 mm O hole to a depth of 80 mm for the safety screw and press the wall plug flush into the wall. . 2. Initially remove the protective foil from the back of ...
Este manual também é adequado para os modelos :Hoods - CD636350/01 (1.32 mb)
Hoods - CD637350/01 (1.32 mb)
Hoods - CD639252/01 (1.32 mb)
Hoods - CD639350/01 (1.32 mb)