Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to. Prior to installation Exhaust-air mode The exhaust air is discharged upwards through a ventilation shaft or directly through the outside wall into the open. For operating in exhaust-air mode, a one- way flap should be mounted inside the wall ventilation box. If no one-way flap was enclosed with the hood, it can be obtained from a specialist retailer. Installing the one-way flap: . Snap the one-way flap into the air pipe. The two lightly sprung flaps must be able to move upwards. If the exhaust air is going to be discharged into the open, a telescopic wall box should be fitted into the outside wall. . For optimum extractor hood efficiency: . Short, smooth air exhaust pipe. . As few bends in the pipe as possible. . Diameter of pipe to be as large as possible and no tight bends in pipe. If long, rough exhaust-air pipes, many pipe bends or smaller pipe diameters are used, the air extraction rate will no longer be at an optimum level and there will be an increase in noise. . Round pipes: We recommend Internal diameter: 120 mm . Flat ducts must have an internal cross section that equates to that of round pipes. There should be no sharp bends. O 150 mm approx. 177 cm2 . . If pipes have different diameters: Insert sealing strip. . For exhaust-air mode, ensure that there is an adequate supply of fresh air. Connecting a O 150 mm exhaust-air pipe: . Mount the pipe directly onto the air outlet on the hood. Circulating-air mode . With activated carbon filter if exhaust-air mode is not possible. The complete installation set can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these operating instructions. Electrical connection The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area apply a bipolar switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over- current category III, in accordance with installation instructions. Warning! Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled. Warning! Power cable replacement must be undertaken by the authorized service assistance centre or similar qualified person. Installation WARNING! Do not connect the appliance to the mains until the installation is fully complete. To a wall-hanging cupboard With 4 screws. 1. Dimensions for the mounting boreholes can be found in, or place a template on the base of the wallhanging cupboard. 2. Mark the mounting holes and make pilot holes with a bradawl. In exhaust-air mode (upwards) mark the exhaust-air opening and saw out. In circulating-air mode, apply the plug supplied to close the exhaust hole (bayonet hooking plug). . . Consider the location of the connection cable; if required, saw out the cupboard. 3. Remove the filter grille (see Instructions for use). 4. Screw the extractor hood to the base of the cupboard. 22 Final assembly Selecting the operating mode: . Exhaust-air mode: Position A . Circulating-air mode: Position F . Refit the grease filter. . Connect to the power supply. Mode d’emploi Description de l’appareil Commutateur Lumiere/Ventilateur Grille du filtre Eclairage Modes de fonctionnement Air evacue a l’exterieur: . Le ventilateur de la hotte aspire les buees de cuisson qui traversent un filtre a graisse avant de regagner l’atmosphere exterieure. . Ce filtre retient les particules grasses solides en suspension dans les buees de cuisson. . Les particules grasses ne se deposent plus dans la cuisine, les odeurs de cuisson disparaissent. Air recycle: . La hotte doit, dans ce cas, etre equipee d’un filtre au charbon actif (voir le filtre et son entretien). Vous pouvez vous procurer le kit demontage complet ainsi que les filtres de rechange aupres de votre revendeur specialise. Vous trouverez les numeros de reference des accessoires correspondants a la fin de la presente notice d’utilisation. . Le ventilateur de la hotte aspirante aspire les buees qui traversent le filtre a graisse et celui a charbon actif avant de revenir dans la cuisine. . Le filtre a graisse retient les particules solides en suspension dans les buees de cuisson. . Le filtre a charbon actif retient les substances odoriferantes. Si vous n’incorporez aucun filtre au charbon actif, impossible de retenir les odeurs presentes dans les buees de cuisson. Avant la pre...
Este manual também é adequado para os modelos :Hoods - DHU965E/01 (4.85 mb)