Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Always use gas hotplates with appropriate cooking utensils. Regulate flame to ensure that it does not lick over the cooking utensil. Risk of burns, risk of damage! if several gas hotplates are operated simultaneously. Never operate two gas hotplates simultaneously on the highest flame for longer than 15 minutes. The housing will become very hot due to the intense heat. Please note: One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners. Risk of fire! ¦ from grease deposits in the metal mesh grease filter. Never work under the appliance with a naked flame (e.g. flambeing) . Always operate the appliance with the metal mesh grease filter. Regularly clean the metal mesh grease filter. ¦ from overheated fats and oils. Heat fats and oils under constant supervision only. Never extinguish fire with water, always use a fire blanket, lid or plate. Caution! Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage. Risk of injury! from the glare of an LED in risk group 1. Do not look directly into the LED light for longer than 100 seconds while it is switched on. Cleaning and care Risk of burns, risk of electric shock! from appliance. Always leave appliance to cool down before cleaning or servicing. Switch off fuse or pull out mains plug. Caution! ¦ Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth. ¦ Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the grain direction only. Do not use any stainless steel cleaners for operator controls. ¦ Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents. Maintenance and repair Risk of fire, risk of injury! from improper repairs. Switch off the fuse or pull out the mains plug. Repairs may be performed by a qualified technician ( electrician) only. Risk of injury! from a defective or damaged appliance. Switch off the fuse or pull out the mains plug and call customer service. Risk of fire, risk of injury! from damaged connection cable. A damaged connection cable must be replaced by a qualified technician (electrician). Risk of burns, risk of electric shock! from defective bulbs. Switch off the fuse or pull out the mains plug. Always replace defective bulbs immediately (leave bulbs to cool down first) to prevent the remaining bulbs from overloading. Operating modes This appliance can be used in exhaust- air mode or circulating- air mode. Exhaust air mode The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. Note: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating appliances. ¦ Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible. ¦ If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. Circulating-air mode The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen. Note: To bind odours in circulating- air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating- air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use. Operation These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes. Control panel variant 1 . . . . . . . Control panel variant 2 Setting the fan ¦ Press the # button to switch on the appliance. The fan starts at setting 2. ¦ The fan can be set manually ( model 1 and model 2) or automatically ( model 2 only) . Manual mode Increase the fan setting by pressing the + button and reduce it by pressing the – button. Automatic mode The appliance must be switched on. ¦ Press button ‘ . ¦ The optimum fan setting 1, 2 or 3 is automatically set via asensor. Sensor control In automatic mode sensors on the extractor hood detect the density of the kitchen fumes. Depending on the setting of the sensors, the extractor hood automatically switches to another fan setting. Factory setting: Setting † Lowest setting: Setting ‹ Highest setting: Setting S If the sensor control responds too quickly or too slowly, it can be changed accordingly: 1. When the fan is switched off, hold down button ‘ for 4 seconds. The settin...
Este manual também é adequado para os modelos :Hoods - D39F56N0GB/02 (1.01 mb)
Hoods - D39F56S0GB/01 (1.01 mb)
Hoods - D39F56S0GB/02 (1.01 mb)