Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• If dirt is particularly stubborn, we recommend using a special grease solvent spray.This can be ordered via the Online Shop. 26 Removing and installing the grease filters Activated carbon filters bind the odours in circulating-air mode. Installing and removing the activated carbon filters 1. Remove the grease filters (see Removing and installing the metal-mesh grease filters). 2. Insert the activated carbon filter. 3. Lock the catch. 4. Reinsert the grease filters (see Removing and installing the metal-mesh grease filters). Changing the activated carbon filter Under normal operation (daily 1 to 2 hours) the activated carbon filters must be replaced approximately 2x year. The activated carbon filter is available from specialist outlets, customer service or the Online Shop (see Optional accessories). Use original filters only. Activated carbon filters do not contain any pollutants. They can be disposed of in the household refuse. Before removing and installing the grease filters, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Removing and installing the metal-mesh grease filters 1. Open the lock and fold down the grease filters. In doing so, hold the underside of the grease filters with your other hand. (for appliances with edge extraction) 2. Clean the grease filters. 3. Reinsert the cleaned grease filters. Changing the bulbs • Before changing the bulbs, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! NOTE: Observe the warranty regulations in the enclosed service booklet. • Defective bulbs should be replaced immediately to avoid overloading the remaining bulbs. Changing the halogen bulbs Halogen bulbs become very hot during operation. Even some time after the appliance has been switched off, there is still a risk of burns! • Before changing the halogen bulbs, ensure that they have cooled down fully. 1.Press on the inner frame of the halogen bulb. 2.Replace the defective bulb with a new one of the same type and equivalent power (see rating plate). NOTE:When inserting halogen bulbs, do not touch the glass tube. Therefore use a clean cloth when inserting the bulb. 3.Close the inner frame of the halogen bulb. NOTE:The inner frame of the halogen bulb will not close unless it was fully opened beforehand. 4.Restore the power supply by inserting the mains plug or switching on the fuse. NOTE:If the light does not function, check whether the bulbs have been inserted correctly. Installation instructions • Prior to installation, always follow the instructions and warnings in the chapter entitled ”Safety instructions”! Exhaust-air mode • The exhaust air is conveyed upwards via a ventilation shaft or directly through the outer wall to the exterior. NOTE: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms which contain heating appliances. • Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the appropriate heating engineer. • Discharge exhaust air in accordance with the official and statutory regulations (e.g. regional building laws). • If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. To ensure optimum performance, the extractor hood requires: – a short, straight exhaust air pipe and – the largest possible pipe diameter. • If pipe bends cannot be avoided, ensure the largest possible radii. NOTE: If long, rough exhaust air pipes, a lot of pipe bends or pipe diameters less than 150 mm are used, the air capacity will be less than optimum and there will be an increase in noise. • Use only pipes or hoses made of noncombustible material for installation of the exhaust air duct. • The manufacturer of the extractor hoods is not responsible for complaints which can be attributed to planning and design of the pipework. Co...
Este manual também é adequado para os modelos :Hoods - D72F58N0/02 (2.95 mb)
Hoods - D72F58N0/03 (2.95 mb)
Hoods - D72F58N0/04 (2.95 mb)
Hoods - D79F58N0/01 (2.95 mb)