Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Gas hobs / Gas cookers Do not use all the gas hotplates simultaneously for a prolonged period (max. 15 minutes) at maximum thermal load, otherwise there is a risk of burns if the housing surfaces are touched or a risk of damage to the extractor hood. If the extractor hood is situated over a gas hob, operate the hood at maximum setting if three or more gas hotplates are operated simultaneously. Operating procedure The most effective method of removing vapours produced during cooking is to: . Switch the ventilator ON as soon as you begin cooking. . Switch the ventilator OFF a few minutes after you have finished cooking. Display for fan setting Fan OFF Reduce fan speed Fan follow-on Saturation indicator Fan ON and increase speed Light Acoustic signal: . When a button is pressed, this is verified by an acoustic signal. Switching off the acoustic signal: . Simultaneously press buttons 0 and + until a signal is emitted after approx. 3 seconds. Switching on the acoustic signal: . Repeat the process. Switching the fan ON . Press the + button. Setting the required fan speed: . Press the + button. The fan speed is increased by one step. . Press the – button. The fan speed is reduced by one step. Switching the fan OFF: . Press the 0 button. The displayed { goes out shortly afterwards. Or: . Keep pressing the – button until the fan switches off. The displayed { goes out shortly afterwards. Intensive setting: Maximum power is obtained at the intensive setting. It is only required for short intervals. . Keep pressing the + button until a c appears in the display. . If the intensive setting is not cancelled by hand, the fan will automatically switch back to step } after 10 minutes. Fan follow-on: . Press the button. The fan runs for 10 minutes at the selected setting and ! is displayed. Then the fan automatically switches off. Lighting: . Briefly press the a button to switch the light on and off. . The light can be switched on at any time, even though the fan is switched off. . Adjusting the brightness: Hold down the a button until the desired brightness is obtained. Switching on the light automatically, e.g. via a timer: . Fan and light must be switched off. Switching on: Simultaneously press the – and ! buttons. . After approx. 3 seconds the light switches on to acknowledge the setting. Switching off: Repeat the process with the light switched on. . After approx. 3 seconds the light switches off to acknowledge the setting. 19 Grease filters: Metal filters are used to trap the greasy element of the vapours that develop during cooking. The filter mats are made from noncombustible metal. Caution: As the filter becomes more and more saturated with grease, not only does the risk of it catching fire increase but the efficiency of the extractor hood can also be adversely affected. Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: U When the grease filters reach saturation point, an acoustic signal is sounded for 10 seconds after the fan has switched off, and an Jappears in the display. The grease filters should be cleaned straight away. Cleaning the metal grease filters: . The filters can be cleaned in a dishwasher. It is however possible that they will become slightly discoloured. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. . When cleaning the filters by hand, soak them in hot soapy water first of all. Do not use aggressive, acidic or caustic cleaners. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. Removing and inserting the metal grease filters: Warning: The halogen bulbs must be switched off and cool. 1. Press the catch on the grease filters inwards and fold the filters down. Filters and maintenance 2. Clean the grease filter. 3. Insert the clean filters back into the hood. 4. Cancel the Jin the display. . Press the Jbutton. 20 Saturation indicator: U b When the activated carbon filter reaches saturation point, an acoustic signal is sounded for 10 seconds after the fan has switched off, and a J b appears in the display. The activated carbon filter should be replaced straight away. Removing the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters. 2. Press the catches at both sides of the filter inwards and lift the carbon filter down and out. Filters and maintenance 3. Engage the catches at both sides. 4. Insert the metal grease filters (see "Removing and inserting the metal grease filters"). 5. Cancel the Jin the display. . Press the Jbutton. 3. Insert the metal grease filters. Replacing the activated carbon filter: . A replacement filter can be obtained from any authorized dealer (see optional accessories). . Use original filters only. By doing so you will obtain maximum performance fro...