Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
fig. 1 Use • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator. Warm food should be allowed to cool to room temperature before being put into the refrigerator. • Nothing should rest against the internal rear wall of the refrigerator, as this will cause frost and possible condensation problems which will be difficult to remove. Setting the temperature You must allow the fridge to settle for at least twenty four hours prior to switching the power on. The fridge will take some time to adjust to the new settings. This will depend on the difference between the old ad new settings, the ambient temperature, the amount of food in the fridge and the number of times the door is opened. To adjust the temperature turn the thermostat control knob clockwise (from off) to the required level. The temperature becomes colder the higher the number on the control. Care and cleaning Always disconnect the appliance from the power before any cleaning or maintenance. • The refrigerator should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • Clean the shelves and balconies separately by hand using soap and water. Do not put them in the dishwasher. • The evaporating tray and water drain hole (at the back of the compartment) should be cleaned periodically to prevent the defrosted water from collecting inside the compartment. The drain plug can be used to clear the drain hole. • Once cleaning is complete, reconnect the mains power supply. • If the appliance is not used for prolonged periods of time or in the event of a prolonged power cut unplug and clean the appliance. The doors should be left slightly open to prevent the formation of mildew and smell. • The door sea soul be cleaned periodically. • Clean the switch, lamp and thermostat control with a dry cloth. Changing the light bulb Disconnect the appliance from the power. • Remove the light cover. • Replace the light cover and reconnect the power after five minutes’ delay as explained on page 3. Troubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The house fuses are intact and the fuse in the plug has not blown. • The thermostat is not set to 0 (off position). • The plug socket is functioning fine. To check this, plug another electrical appliance in to see if the socket is working. • The temperature of the room is adequate (10oC or above). If the appliance is working, but not very well • The appliance is not overloaded. • The thermostat is set to an appropriate temperature. • The door is closing properly. • The cooling system at the rear of the appliance is clean and free of dust, and not touching the rear wall. • There is enough ventilation at the side and rear walls. • The temperature of the room is adequate (10oC or above). If the appliance is noisy • The appliance is level and stable. • The side and rear walls are clear, and there is nothing resting on the appliance. • The cooling gas in the refrigerator will make a slight bubbling noise, even when the compressor is not running. If there is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear. Installation And Ventilation This appliance must never be installed close to heat sources i.e. heating elements, cookers or in damp places The diagram shows the ventilation requirements for your product. Failure to provide adequate ventilation can lead to increased running costs and premature failure and may invalidate the warranty provided with the product. 1780-1783 540540fig. 2 Reversing the door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Loosen the top hinge fixing screws and remove the top hinge, taking care to support the weight of the door. 2. Lift the door from the bottom hinge and place on a soft surface to protect the door from damage. 3. Refit the hinge taken from the top to the opposite lower corner, as in figure 3. 4. Replace the door and refit the hinge taken from the lower corner to the opposite top corner. 5. Adjust the hinges to ensure the door is aligned correctly. fig. 3 Mounting the Fascia Door • Using a screwdriver, fix the mounting brackets to the • appliance door, as shown in figure 4. • Position the appliance within the unit. Ensure that there is a gap of 3 to 4 mm between the non-hinged side and the cabinet wall. • Locate the slider in the bracket and fix the slider to the fascia door 20 to 22 mm from the edge of the fascia as shown in figure 5, ensuring that the slider is positioned centrally and horizontally within the bracket. Tighten securely by hand. • Fill the gap on the non-hinged side with the seal strip • provid...