Assessments - 3, GPA: 3.7 ( )

Fabricante : Antec Arquivo Tamanho: 1.02 mb Arquivo Nome : Língua de Ensino:

Note: Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Slide the cage back into the case and fasten the thumbscrew. 6. Find a Molex or SATA connector on the power supply and connect it to the hard drive. 7. Repeat the same procedure for the other drives. External 3.5” Drive Installation There is one external 3.5” drive bay. 1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay. 2. Find a pair of 3.5”drive rails in the box containing the top fan spoiler. 3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on the outside and facing forward. 4. Slide the device into the drive bay until it clicks into place. 5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive. 5.25” Device Installation There are four 5.25” drive bays that need a total of 8 drive rails. 1. Carefully remove the plastic drive bay cover and the metal plate covering the drive bay. 2. Mount the drive rails onto the sides of the 5.25” device. Make sure the metal portion is angled on the outside towards the outside of the case. 3. Slide the device into the drive bay until it clicks into place. 4. Mount the other devices accordingly. 5. Connect a 4-pin Molex connector from the power supply to the 4-pin connector on each of the devices. Cooling System The TriCool™ fan: The case includes three installed 120mm TriCool™ fans. The three-speed fans let you choose between quiet performance or maximum cooling (see specifications below). Note: The minimum voltage to start the fan is 5V. We recommend our users to set the fan speed to High if you choose to connect the fan to a fan control device or to the Fan-Only connector found on some Antec power supplies. 5 A fan-controller regulates the fan speed by varying the voltage to it. The voltage may start as low as 4.5V to 5V. Connecting a TriCool™ set on Medium or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan controller will be further reduced by the TriCool™ circuitry below 5V. The Top and Rear Exhaust TriCool™ Fans External fan switches allow adjusting the speed of these two fans without having to open the case. Note: We recommend that our users set these two fans to Low in order to cool the CPU more effectively. The two fans are mounted so that the air is blowing out of the case. The top fan comes with a spoiler to mount on the top of the case. To install the spoiler: 1. With the higher end of the spoiler facing the rear of the case, carefully align the tabs of the spoiler with the notches on the case. 2. Insert the tabs to the notches and slide the spoiler towards the front of the case until it clicks into position. The Lower Chamber TriCool™ Fan This is a standard 120mm fan. This fan is placed in the middle of the lower chamber which acts like a wind tunnel when side panels are closed, which guarantees the air will move from the front to the rear when the fan turns. Note: We recommend setting the speed to Medium or Low. Specifications: Size: 120 x 120 x 25.4mm TriCool™ Fan Rated Voltage: DC 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Air Flow Static Acoustical Input Current Pressure Noise Power High 2000 RPM 0.24A (Max.) 2.24 m. / min (79 CFM) 2.54 mm-H2O (0.10 inch-H2O) 30 dBA 2.9 W Medium 1600 RPM 0.2A 1.59 m. / min (56 CFM) 1.53 mm-H2O (0.06 inch-H2O) 28 dBA 2.4 W Low 1200 RPM 0.13A 1.1 m. / min (39 CFM) 0.92 mm-H2O (0.04 inch-H2O) 25 dBA 1.6 W The Optional Fans There are two optional 120mm fan mounts – a front fan (in front of the upper HDD cage) and a middle fan (at the rear end of the upper HDD cage). These two fans should be installed so that the air is blowing into the case from the front. The Front Fan – The front fan is designed to enhance the HDD cooling. If you decide to mount any HDD into the upper cage, you will not be able to use the middle fan. 6 The Middle Fan – The middle fan is especially designed to cool the VGA card and even a dual VGA card configuration. In this case the HDD cage becomes a duct drawing fresh cool air from the front of the case. You can choose to mount only the middle fan or you can mount both the front and the middle fans to enhance the cooling as two fans will serve a push and pull action bringing the air more efficiently. 1. Find the two fan wire brackets from the tool bag. 2. Install the wire brackets into the HDD cage. 3. Clip the fan into position. In order to build a quieter system we recommend NOT installing the optional fans if not necessary for the cooling of your components. If you choose to install them we recommend using Antec 120mm TriCool™ fans and setting the speed to Low. Optional rubber grommeted ports There are two rubber grommeted ports in the rear panel. You can use them to route tubing for external liquid cooling devices. The Washable Air Filters There are two filters located behind the front grilles. From time to time it...

Baixe o seu

Para fazer o download, introduza 2 dígitos :