Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded. Identification of parts Freezer Refrigerator Milk product corner Lamp Shelf Wine holder (Plastic or wire) Door rack (1 piece or 2pieces) Shelf Snack drawer (Optional) Shelf (Folding or Normal) Refreshment center (Optional) Egg box Door rack (1 piece or 2pieces) Vegetable drawer (1 or 2) Door rack Humidity switch Miracle Zone (Optional) Fresh compartment (Optional) Conversion switch (Meats/Vegetables) (Optional) NOTE 1 If you found some parts missing from your unit, they may be parts only used in other models, (i.e. the "Refreshment center" is not included in all models) €> Installation Select a good location Disposal of the old appliance Where to Install 1. Place your appliance where it is easy to use. 2. Avoid placing the unit near heat sources, direct sunlight or moisture. 3. To ensure proper air circulation around the fridge -freezer, please maintain sufficient space on both the sides as well as top and maintain at least 2 inches (5 cm) from the rear wall. 4. To avoid vibrations, the appliance must be leveled. 5. Don't install the appliance below 5°C. It may cause affect the performance. This appliance contains fluid (refrigerant, lubricant)and is made of parts and materials which are reusable and/or recyclable. All the important materials should be sent to the collection center of waste material and can be reused after rework (recycling). For take back, please contact with the local agency. e Installation A Warning Remove lower cover and then feed water tube Remove the freezer compartment door Remove the refrigerator door Door removal Electric Shock Hazard Disconnect electrical supply to refrigerator before installing Failure to do so could result in death or serious injury. If your access door is too narrow for the refrigerator to pass through, remove the refrigerator door and pass the refrigerator laterally. Remove the lower cover by lifting upward, and remove clip, and then pull up the feed water tube while pressing area © shown in the figure to the right. NOTE • If a tube end is deformed or abraded, cut the part away. 1) Removing the hinge cover by loosening the screws. Separate all connection wires except for the earth line after. Feed water tube Upper hinge Connection \ wires Earth line 2) Remove the keeper by rotating it counter clockwise (©) and then lifting the upper hinge up (CD). NOTE • When removing the upper hinge, be careful that the door does not fall forwards . Upper hinge 3) Remove the freezer compartment door by lifting it upward. This time, the door should be lifted enough for the feed water pipe tube to be completely pulled out. Lower hinge NOTE • Move the refrigerator compartment door passing through the access door and lay it down, but be careful not to damage the feed water pipe tube. 1) Loosen the hinge cover screws and remove the cover. Remove connection wire, if any, except for the earth line. 2) Remove keeper by rotating it clockwise (®) and then remove the upper hinge by lifting it up (©). 3) Remove the refrigerator compartment door by lifting it up. O Lower hinge Installation Pass the refrigerator Before installation A\ Warning Pass the refrigerator laterally through the access door as shown in the right figure. Door replacement Mount them in the reverse sequence of removal after they pass through the access door. Feed water pipe installation ■ Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.). ■ If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed. ■ Keep the total length of the feed water pipe tube within 8 m and be careful for the tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed owing to the drain water pressure. ■ Install the feed water pipe tube at a place free from heat. ■ Connect to potable water supply only. ■ Refer to instructions with water filter kit for installation. Q Installation If the height of freezer compartment door is different from the height of Refrigerator compartment door After leveling the door height Next Height adjustment If the freezer compartment door is lower than the refrigerator compartment door Level the door by inserting flat (-type) driver into the groove of the left height adjusting screw and rotate it clockwise (®). If the freezer compartment door is higher than the refrigerator compartment door Level the door by inserting flat (-type) driver into the groove of the right height adjusting screw anc rotate it clockwise (®). Height difference Height difference When the freezer door does not align with the height of ...