Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Separating the Water Supply Line from the Refrigerator 1. Remove the water line by pressing the coupler 1 and pulling the water line 2 away. Do not cut the water line. Gently separate it from the coupler. 2. Removing the freezer door A few things to mention fi rst. • Make sure that you lift the door straight up so the hinges are not bent or broken. • Be careful not to pinch the water tubing and wire harness on the door. • Place doors on a protected surface to prevent scratching or damage. 1. With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and then disconnect the wires by gently pulling them apart 2 . 2. Remove hinge screws 3 and the ground screw 4 by turning counter-clockwise, and take off the upper hinge 5 . Be careful that the door does not fall on you as you are removing it 3. Next, remove the door from the lower hinge 6 by carefully lifting the door straight up 7 . Be careful not to pinch the water tubing and wire harness on the door. 4. Remove the lower hinge 8 using a hex wrench. 2 1 3 4 5 7 6 1 2 DA99-02318N-10.indb Sec4:15 13. 6. 21. 1:52 16_ setting up Removing the Fridge Door 1. With the door closed, remove the upper hinge cover 1 using a screwdriver. 2. Remove hinge screws 2 and the ground screw 3 by turning counter-clockwise, and take off the upper hinge 4 . Be careful that the door does not fall on you as you are removing it 3. Remove the door from the lower hinge 5 by lifting the door straight up 6 . 4. Remove the lower hinge 7 from the bracket 8 by gently lifting the lower hinge upwards. REATTACHING THE REFRIGERATOR DOORS Once you have safely placed your refrigerator where you plan for it to stay, it is time to put the doors back on. Reattaching the Freezer Door 1. Replace the freezer door by inserting the water line 1 back into the lower corner of the door and then into the hole on the lower hinge 2 . Gently pull the water line back down so that it runs straight, with no kinks or bends. 2. Insert the upper hinge shaft 3 into the hole on the corner of the freezer door 4 . Make sure the hinge is level between the upper hinge hole 5 and the hole of the cabinet 6 and reattach the hinge screws 7 and ground screw 8 by turning in a clockwise direction. Reconnect the wires. 3. Place the front part of the upper hinge cover 9 on the front of the upper hinge 10 and reattach with the screw. 4 2 3 1 4 5 6 7 8 3 1 2 10 9 DA99-02318N-10.indb Sec4:16 13. 6. 21. 1:52 setting up _17 01 SETTING UP Reattaching the Fridge Door 1. Insert the lower hinge 1 back into the lower hinge bracket 2 . 2. Fit the hole in the corner of the fridge door 3 over the lower hinge 4 . 3. Insert the upper hinge shaft 5 into the hole on the hinge 6 . Make sure the hinge is level between the upper hinge hole 7 and the hole on the top of the cabinet 8 . Then, reattach hinge screws 9 and the ground screw 10 by turning it in a clock wise direction. 4. Place the front part of the upper hinge cover 11 on the front of the upper hinge 12 and reattach it with the screw. Reattaching the Water Supply Line 1. Insert the water line 2 into the coupler 1 . 2. The Water Line must be fully Inserted to the center of transparent coupler to prevent water leakage from the dispenser. 3. Insert the clip in the install pack and check that it holds the line fi rmly. Reattaching the Front Leg Cover Before attaching the cover, check water connector for leakage. Replace the front leg cover by turning the three screws clockwise, as shown in the fi gure. 1 2 1 2 3 4 12 11 Center of transparent coupler clip A (1/4”) (6.35mm) DA99-02318N-10.indb Sec4:17 13. 6. 21. 1:52 LEVELLING THE REFRIGERATOR Now that the doors are back on the refrigerator, you will want to make sure the refrigerator is level so you can then make final adjustments. If the refrigerator is not level, it will not be possible to get the doors perfectly even. The front of the refrigerator is also adjustable. When the Freezer door is lower than the fridge Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the freezer. Leg Screw Driver When the Freezer door is higher than the fridge Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the fridge. Leg Screw Driver Refer to the next section for the best way to make very minor adjustments to the doors. MAKING MINOR ADJUSTMENTS TO THE DOORS Remember, a level refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on levelling the refrigerator. When the door of the freezer is higher than the fridge Adjustment part In the process for adjusting both the doors is the same. Open the doors and adjust them, one at a time, as follows: 1. Unscrew the nut 1 from the lower hinge until Bolt it reaches the upper end of the 2bolt . When you release the nut 1 , make sure that 3 2 1 Wrench Nut you use the Allen wrench provided 2 3 to loosen the bolt in a counter-clockwise direc...
Este manual também é adequado para os modelos :Frigoríficos - RSH5ZL2A (11.94 mb)
Frigoríficos - RSH5ZERS (11.94 mb)
Frigoríficos - RSH5UTPN (11.94 mb)
Frigoríficos - RSH5TERS (11.94 mb)