Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury. The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord. • EXTENSION CORD Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes. • SURGE PROTECTOR Most electrical appliances use a series of electric control boards to operate. These boards are very susceptible to power surges and could be damaged or destroyed. If the appliance is going to be used in an area or if your city / country is prone to power surges / outages; it is suggested that you use a power surge protector for all electrical devices / appliances you use. The surge protector that you select must have a surge block high enough to protect the appliance it is connected to. If you have any questions regarding the type and size of surge protector needed contact a licensed electrician in your area. Damages due to power surges are not considered a manufacturer covered defect and will void your product warranty. 9 OPERATING YOUR WINE CHILLER It is recommended you install the Wine Chiller in a place where the ambient temperature is between 23.-26.C/ 72.-78.F. If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The range of 5.-18.C/40.-65.F may not be reached. Recommended Temperatures for Chilling Wine. Red Wines 15. - 18. C 58 – 65. F Dry/White Wines 9. - 14. C 48 – 57. F Rose Wines 10. - 11. C 49 – 51. F Sparkling Wines 5. - 8. C 40 – 47. F You can select temperature display setting from Fahrenheit to Celsius degree by holding down UP and DOWN buttons at the same time for three seconds. Fahrenheit or Celsius degrees indicator will appear in blue color in the temperature display window. • ON/OFF POWER To turn OFF the appliance, touch the mark and hold for 2 seconds. • SETTING THE TEMPERATURE CONTROL . You can set the temperature as you desire by touching the UP or DOWN mark. When you touch the two marks for the first time, the LED readout will show the original temperature set at previous time (the temperature preset at the factory is 12.C/54.F). . The temperature that you desire to set will increase 1.F or 1.C if you touch the UP mark once, on the contrary the temperature will decrease 1.F or 1.C if you touch the DOWN mark once. . When you store mostly red wines, the temperature which you control by touching the above two marks need to be set at between 15. - 18.C/58. - 65.F and the LED lamp under “RED” will be lit red. . When you store mostly white wines, the temperature needs to be set at between 9. - 14.C/48. 57 .F and the LED lamp under “WHITE” will be lit green. . When you store mostly sparkling wines, the temperature needs to be set at between 5. - 8.C/40. 47 .F and the LED lamp under “SPARKL” will be lit amber. . The temperature inside the unit will be appeared in blue color in the display window. NOTE: . If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the Wine Chiller will not start. . When you use the wine chiller for the first time or restart the wine chiller after having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the LED readout. This is normal and it is due to the length of the activation time. Once the wine chiller is running for a few hours everything will be back to normal. 10 • STORAGE Many bottles may differ in size and dimensions. As such the actual number of bottles you may be able to store may vary. NOTE: You can place 48 standard bottles in this wine chiller. Bottle capacities are approximate maximums when storing traditional Bordeaux 750 ML bottles and ...