Assessments - 5, GPA: 4.6 ( )

Fabricante : Avanti Arquivo Tamanho: 145.58 kb Arquivo Nome : 200372en.pdf Língua de Ensino:

The following table shows which ambient temperature is correct for each climate classification: each climate classification: Climate classification ffor an ambient temperature of SN +10 bis +32 .C N +16 bis +32 .C ST +18 bis +38 .C T +18 bis +43 .C If installation next to a source of heat is unavoidable, the following minimum clearances must be maintained at the sides of the appliance: . for electric cookers 3 cm; . for oil and coal fired ranges 30 cm. If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance. If the refrigeration appliance is installed next to another refrigerator or freezer a clearance of 5 cm at the sides is required, in order to prevent the formation of condensation on the outside of the appliance. PR153AEG70 PR153AEG70 Your appliance needs air Air flows in from under the door, at the front, and flows out upwards, over the back. For correct air circulation, it is important that the ventilation openings are not covered or obstructed. Important! If the appliance is positioned under a kitchen wall unit, a minimum clearance of 10 cm must be left between the top of the appliance and the overhanging wall unit. Rear spacers Fit the rear spacers contained in the documentation bag to ensure even dissipation of heat genereted during operation. Proceed in the sequence illustrated by the figures. Levelling the appliance Place the appliance on a flat hard floor. Two adjustable feet on the front of the appliance enable it to accurately levelled by screwingthem in or out as required. Rehingeing the door The side at which the door opens can be changed from the right side (factory adjustment) to the left side, if the installation site requires. Warning! When changing the side at which the door opens, the appliance may not be connected to the mains. Remove plug from the mains before hand. Procced as follow: 1. Remove the ventilationgrill (D). 2. Remove plug (F) and refit it on the opposite side of the ventilationgrill. 3. Unscrew the bottom hinge and remove the freezer compartment door by pulling it downwards. 4. Re-tighten the screws. 5. Remove the screw masking plugs from the bottm left-hand side and refit them on the right- hand side. 6. Unscrew the two screws on the bottom left-hand side. 7. Unscrew the middle hinge and remove the refrigerator compartment door by pulling it downwards. 8. With a screwdriver, unscrew the two masking plugs covering the holes on the left-hand side and refit them on the right- hand side. 9. Unscrew the pin from the top hinge and refit it on the left- hand side. Remember to fit the washers. 10. Slide the refrigerator compartment door onto the top pin. 11. Insert the middle hinge into the bottom of the refrigerator compartment door. Remember to fit the washers. 12. Fully screw up the middle hinge. 13. Fit the freezer compartment door onto the middle hinge. F D PR185 F F E F H C B A PR19 PR228 14. Insert the bottom hinge into the bottom of the freezer compartment door. 15. Fully screw down the bottom hinge. 16. Re-assemble the ventilation- grill (D) 17. Unscrew the handles. Refit them on the opposite side after having piercing the plugs with a punch. Cover the holes left open with the plugs contained in the documentation pack. Prior to Initial Start.Up . Please clean the appliance interior and all accessories prior to initial start-up (see section: OCleaning and CareO). Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING . THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is inside, on the left. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Important! The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug, proceed as follows: 1. The wire coloured green and yellow must be connected to the terminal marked with the letter aEO or by the earth symbol or coloured green and yellow. 2. The wire coloured blue must be connected to the terminal aNO or coloured black. 3. The wire coloured brown must be connected to the terminal marked aLO or coloured red. 4. Upon completion there must be not cut, or stray strands of wire present and the cord clamp must be secure over the outer sheat. Warning! A cut-off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut-off plug is disposed of safely. Control panel 4 3 2 10 123 4 The thermostat knob (4) is...

Baixe o seu

Para fazer o download, introduza 2 dígitos :