Assessments - 3, GPA: 4 ( )

Fabricante : Avanti Arquivo Tamanho: 181.82 kb Arquivo Nome : 209862en.pdf Língua de Ensino:

Unusual noises. Appliance is not level. Readjust the feet. The appliance is touching Move the appliance slightly. the wall or other objects. A component, e.g. a pipe, If necessary, carefully bend on the rear of the appliance the component out of the is touching another part of way. the appliance or the wall. The compressor does not This is normal, no error has The compressor starts after start immediately after chan- occurred. a period of time. ging the temperature setting. Water on the floor or on sto- Water drain hole is blocked. See the "Cleaning and rage shelves. Care" section. Changing the light bulb Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the circuit breaker. Light bulb data: 220-240 V, max. 15 W 1. To switch off the appliance, turn the temperature regulator to position "0". 2. Unplug the mains plug. 3. To change the light bulb, undo the screw. 4. Press the light bulb cover as shown and slide it backwards. 5. Change the defective light 6. Refit the light bulb cover screw. 7. Put the refrigerator D411 What to do if ... Correcting Malfunctions A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other work on the appliance if the following information does not provide assistance in your specific case. Warning! Repairs to refrigerators/freezers may only be performed by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your specialist dealer or our Customer Service. Malfunction Possible Cause Remedy Appliance is not switched on Switch on the appliance. Mains plug is not plugged in Insert mains plug. or is loose. Fuse has blown or is defec- Check fuse, replace if Appliance does not work. tive. necessary. Socket is defective. Mains malfunctions are to be corrected by an electrician. Appliance cools too much. Temperature is set too cold. Turn the temperature regulator to a warmer setting temporarily.. Temperature is not properly Please look in the "Initial adjusted. Start Up" section. Door was open for an exten- Open the door only as long ded period. as necessary. A large quantity of warm Turn the temperature regu- The food is too warm. food was placed in the lator to a colder setting tem- appliance within the last 24 porarily. hours. The appliance is near a heat Please look in the "Installa source. tion location" section. Interior lighting does not Light bulb is defective. Please look in the "Chanwork. ging the Light Bulb" section. Transportschutz entfernen Das Gerat sowie Teile der Innenausstattung sind fur den Transport geschutzt. • Alle Klebebander sowie Polsterteile aus dem Gerateinnenraum entfernen. Aufstellen Aufstellort Das Gerat soll in einem gut belufteten und trockenen Raum stehen. Die Umgebungstemperatur wirkt sich auf den Stromverbrauch aus. Daher sollte das Gerat – nicht direkter Sonneneinstrahlung ausgesetzt sein; – nicht an Heizkorpern, neben einem Herd oder sonstigen Warmequellen stehen; – nur an einem Ort stehen, dessen Umgebungstemperatur der Klimaklasse entspricht, fur die das Gerat ausgelegt ist. Die Klimaklasse finden Sie auf dem Typschild, das sich links im Innenraum des Kuhlraumes befindet. Nachstehende Tabelle zeigt, welche Umgebungstemperatur welcher Klimaklasse zugeordnet ist: Klimaklasse fur Umgebungstemperatur von SN +10 bis +32 °C N +16 bis +32 °C ST +18 bis +38 °C T +18 bis +43 °C Ist die Aufstellung neben einer Warmequelle sind folgende seitliche Mindestabstande – zu Elektroherden 3 cm; – zu Ol- und Kohleherden Konnen diese Abstande nicht Steht das Kaltegerat neben einem anderen Kuhl- oder Gefriergerat, ist ein seitlicher Abstand von 5 c...

Baixe o seu

Para fazer o download, introduza 2 dígitos :