Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Single-phase 60Hz Output Voltage Step wave Frequency 60Hz Battery Backup Time Desktop computer +15" monitor 10 min. Desktop computer +17" monitor 13 min. Recharge Time 16 hours to 90% Environment Temperature 0~40°C Humidity 0~90% Safety Safety UL1778 / c-UL Regulation EMI FCC Class B EMS IEEE C62.41 category A/IEC1000-4-5 / Level 2 Appearance Dimensions (W * H * D) 134 x 89 x 357mm Net Weight 2.9kg. 3.1kg. Installation Note: Before installation, please inspect the Unit. Make sure that nothing inside the package is damaged. A. Connect to AC Utility Power Plug in the AC cord to a wall outlet. Please make sure there are no devices plugged into the Unit. Check to see whether the “SITE WIRING FAULT” indicator is lit. If it is lit, please have the utility wiring inspected by an electrician. B. Charge the Battery For best results, charge the battery for eight hours prior to initial use. The Unit charges its battery whenever it is connected to the utility power. C. Turn on the Unit Turn on your Unit by depressing the “On/Off” button for approximately two seconds. You will see the green indicator light come on. D. Plug in Power Devices Plug your devices into the AC outlets on the Unit. To use the Unit as a master on/off switch, make sure all of the loads are switched on. Caution: Never connect a laser printer or scanner to the backup outlets along with other computer equipment. A laser printer or scanner draws significantly more power when in use than when idle. This may overload the Battery Backup. E. Connect the Phone/Fax/Modem Lines 1. Connect a single phone/fax/modem line into the surge-protected outlets on the side of the Unit. The RJ11 modular outlets accept standard single-line telephone connections. 2. Plug one end of the phone cable into your telephone wall jack and plug the other end into the jack marked “IN”. You may now plug a phone, fax, or modem into either of the two jacks marked “OUT”. (See Fig. 3) Fig. 3 Note: This connection is optional but highly recommended as phone/fax/ modem lines often carry dangerous surges and spikes. The Unit works properly without a phone/fax/modem connection. Caution: The phone/fax/modem protection feature could be rendered inoperable if improperly installed. Make sure that the telephone line from the wall is plugged into the connector marked “IN”, and the devices to be protected (phone/fax/ modem) are plugged into the connector marked “OUT”. F Connect the USB (Universal Serial Port) Communication Port (See #4 on Fig. 2) A USB port is provided to relay the signal to support Windows. To fully utilize the Belkin Automatic Power Management Software, you will need to connect the Unit to your computer. Connect the USB cable to the Unit, then connect the other end to your computer’s USB port. G. Install Belkin APM Software a) System requirements • 128 MB RAM of memory at least (256MB is recommended) • 256 colors and 800 * 600 resolution or above display is recommended • 160 MB of disk space or above • An available communication port (RS-232 Serial Port or USB port) is needed while connecting to UPS with a special connecting cable. Mac OS X, Linux or Unix operating system, the user must have the access authority as the super user CP/IP protocol must be installed to support network management user needs to have the access authority as the administrator b) Platforms supported by Belkin APM Software. The following operating system (OS) is arranged by the alphabetical order: Introduction Package Contents System Requirements Overview |Features and Functions 3. The “On/Off” button has four functions: (See #3 on Fig. 1) 1. Turns on the Unit. Depress button at least two seconds. The green light illuminates. 2. Cold start function. If the battery is charged, the Unit will work without being plugged into an outlet. Depress and hold the key for at least two seconds to turn on the Unit. 3. Silence function. During “On Battery Mode”, the audible sound can be turned “ON” or “OFF” by depressing the switch for less than 1.5 seconds. 4. Battery test function. During “On-Line Mode”, depressing the switch for less than 1.5 seconds causes the Unit to perform a battery test in backup mode. Overview |Side Panel “ ” ” optional. The Unit will provide backup power whether or not the cable and software are installed; however, without them you will be unable to utilize the data management product features. Battery Replacement Procedure Replacement requires removing the battery cover plate on the back or bottom of the Battery Backup. No tools are needed. To replace the battery: 1. Push the connector in the arrowhead direction.(Fig.1) 2. Remove the battery cover plate and the battery from the Unit(Fig.2) 3. Disconnect the insulated connectors from the battery terminals, and replace the new battery pack. (Fig. 3) 4. Close the battery cover plate, then lock the connector. (Fig.4). Overview |Alarms Backup (Slow Alarm) When the Unit is in “backup” mode (running on battery), the YELLOW LED illuminates and the Un...
Este manual também é adequado para os modelos :carregadores - F6H550-USB (901.63 kb)