Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
If necessary, wear an ANSI approved breathing respirator to avoid hydrogen gas fumes. 18. Use this Charger only with lead acid, rechargeable type batteries. Remove the battery caps to check liquid level inside battery. If liquid is not present, or if liquid appears to be frozen, do not attempt to charge the battery. 19. Proper Battery Care: Battery leakage may occur under extreme usage or temperature conditions. If battery fluid comes in contact with skin, wash with soap SKU 92775 For technical questions, please call 1-800-444-3353 PAGE 8 20. Performance of the Charger (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect equipment performance. People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. In addition, people with pacemakers should adhere to the following: Avoid operating power equipment alone. Don’t use a power equipment with the power switch(s) locked on. Properly maintain and inspect all power equipment before use to avoid electrical shock. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS 21. WARNING! 22. WARNING! CONTROL PANEL FEATURES FIGURE D CHARGING CURRENT SELECTOR (1) POWER ON (2) BATTERY CHARGING (3) BATTERY CHARGED (4) LOW BATTERY (5) POWER SWITCH (6) SKU 92775 For technical questions, please call 1-800-444-3353 PAGE 9 1. Charging Current Selector (1): The Charging Current Selector is used for selecting a charging current of either 0.25 AMPs, 0.50 AMPs, or 0.90 AMPs depending upon the 12 volt battery that is to be charged. Use a digital voltmeter (not included) to determine the voltage of the battery. Check the battery manufacturer’s recommended charging current. Then, set the Charging Current Selector to the appropriate Amperage. (See Figure D.) 2. Power On (2): When illuminated, the Power On feature indicates the Battery Charger is on and ready for use. (See Figure D.) 3. Battery Charging (3): After properly connecting the Charger Clamps to the battery, selecting the correct charging current, and turning on the Batter Charger, the Battery Charging feature will illuminate indicating proper functioning of the Battery Charger. If the Battery Charging feature does not illuminate, the voltage of the battery is below 9 volts, and the battery will notcharge. (See Figure D.) 4. Battery Charged (4): When illuminated, the Battery Charged feature indicates the battery is fully charged and may then be disconnected from the Battery Charger. (See Figure D.) 5. Low Battery (5): When illuminated, the Low Battery feature indicates the battery connected will not be charged as its voltage is below 9 volts. The battery should be recycled according to local guidelines. (See Figure D.) 6. Power Switch (6): Always properly connect the Charger Clamps to the battery, and select the correct charging current beforeturning the Power Switch to its “ON” position. Once the battery(s) is charged, turn the Power Switch to its “OFF” position. Thendisconnect the Charger Clamps, and remove the battery(s). (See Figure D.) 7. Charger Clamps: Never allow the Red and Black Charger Clamps to touch each other or the same metal object. Always connect the Black Charger Clamp of the Charger to the negative (--) terminal on the battery. Always connect the Red Charger Clamp of the Charger to the positive (+) terminal on the battery. When connecting the Charger Clamps to the terminals on a battery, always connect the Red Charger Clamp first, then connect the Black Charger Clamp. When disconnecting the Charger Clamps, always disconnect the Black Charger Clamp first, then disconnect the Red Charger Clamp. Make all Charger Clamp connections before plugging the Charger’s Power Cord Plug into a 120 volt, grounded, electrical outlet and turning on the Power Switch. 8. Internal 12 Volt Relay (8): The Battery Charger features an internal 12 Volt Relay to protect the Battery Charger from a short circuit and reverse polarity. The 12 Volt Relay will not connect the battery to the Battery Charger unless the battery voltage is more than 9 volts and connected to the proper polarity. SKU 92775 For technical questions, please call 1-800-444-3353 PAGE 10 9. 3 AMP Fuse (9): The 3 AMP Fuse is located on the rear panel of the Battery Charger. In the event the Power On (2) feature on any of the six separate cir cuits does notilluminate, turn Power Switch(es) (6) to the “OFF” positions and unplug the Battery Charger from its electrical outlet. Temporarily remove the Fuse Cap. Pull out and remove the 3 AMP Fuse to check for a melted wire strand within the Fuse. If necessary, insert a new 3 AMP...
Este manual também é adequado para os modelos :carregadores - 92775 (495.38 kb)