Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Double press Double press Switch Charge jack Battery charger To AC power outlet Battery indicator 1 2 Charging Indicator x1 Screw Lens unit Battery Battery connector Body Rubber packing 2 3 OK NO! Left side Battry guide #533-8827 H34 Bracket #534-1859 NiMH 4.8v 780mAH UL:#534-1860 UK:#534-1861 EC:#534-1862 AS:#534-1864 CHR-780mAH 4.8v NiMH SPARE PARTS ENG COMPONENTS Light unit H34 Bracket Battery charger FOR SAFE OPERATION Do not place it within children's reach. In preparation for unexpected battery shutoff, we recommend you carry a dry-cell battery light unit with you. If the light unit or parts become dirty with mud, etc., clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. Mount the light unit more than 10 cm away from the wireless meter. When it is mounted too close, the transmission may be affected adversely. This product has waterproof features that allow you to use it in rain. Do not use it soaked in water. Before Initial Use Before shipment, it is charged enough to check the light. Be sure to charge it before use, according to the instructions "How to charge." •• • • • INTRODUCTION Before using the light, please read this manual and the attached “NiMh Batteries” thoroughly, and keep them for future reference. Thank you very much for purchasing the CATEYE "SINGLE SHOT HL-EL600RC." This product is a high power rechargeable light unit that integrates a high power LED and a nickel metal-hydride rechargeable battery into a compact body. HOW TO MOUNT Wrap the bracket strap around the handlebar, and put it in the dial. Securely tighten the strap by turning the dial. Cut off the excess bracket strap extending from the dial. I n s e r t t h e l i g h t u n i t t o the bracket until it clicks. To remove, pull out while pressing the release button. CAUTION!: Make sure to tighten the dial by hand. If you tighten it too hard with a tool, the screw threads may be stripped. When the angle adjustment on the right and left sides is loose, tighten the screw (*1). Round off the cut edge of the bracket strap to prevent injury. How to Adjust Beam Angle Slightly loosen the dial on the bracket. Adjust the light unit angle so that the light is not directed to oncoming cars. When the dial is too fi rm to loosen, wash it slightly with water to loosen it. Do not loosen the dial too much, or the bracket strap may come off. Loosen the dial just enough to allow the bracket to move slightly. Securely tighten the dial after adjusting the strap. It can also be adjusted 10 degrees to the left and right. 1.. 2.. 3.. 4.. • • • 5.. 6.. * * * 3 How to charge Open the charge jack cover at the back of the light unit to connect the battery charger plug. Plug the battery charger to an AC outlet. After charging, remove the plug and close the charge jack cover. 1.. 2.. 3.. HOW TO REPLACE BATTERY HOW TO USE 1 Lighting (lighting pattern selection) The lighting pattern is selected using a switch. Standard charging time Blinking red light : Charging Green light : Charging is completed Approx. 5 hours Charging indicator state Be sure to use the special purpose battery charger. Charging and lighting times are approximate values, and will vary by environmental and user conditions. * * ON - OFF : Long press Hi - Low : Single press Flash : Quick double press Hi : About 2 hours Low : About 6 hours Flash : About 24 hours Switch Standard continuous lighting time 2 Remaining battery capacity When the battery indicator lights up red, the battery is almost shutoff. Charge the battery as soon as possible. Remove 2 screws at the front of the lens using a 2.5 mm Allen wrench. Slowly pull out the lens unit from the body. Remove the battery connector connected to the board, and replace it with a new battery. Place the battery on the tray, and insert it to the body in place, and secure it with 2 screws. CAUTION!: The lens unit is a precision part; therefore, never disassemble it. Otherwise, the optimum light distribution may be lost. To maintain its waterproof features, assemble the lens unit with a rubber packing-sheet correctly. In order to avoid cable damage, when re-assembling the light, make sure the battery cable is routed inside the battery guide as shown below. 1.. 2.. 3.. 4.. • • • SPECIFICATIONS Light source High power white LED x 1 Battery NiMH 4.8v 780mAH Battery charger CHR-780mAH 4.8v NiMH Operating time Hi : Approx. 2 hours Low : Approx. 6 hours Flash : Approx. 24 hours Standard charging time Approx. 5 hours Temperature range Charging : 32°F – 104°F (0°C – 40°C) Operating : 5°F – 113°F (-15°C – 45°C) Recharge/discharge number of times About 300 times (until the rated capacity drops to 50%) Dimensions/weight 3-17/64” x 2-23/64” x 1-1/2” (83 x 60 x 38 mm) / 4.09 oz (116 g) * The specifi cations and design are subject to change without notice. Service & Research Address for USA CATEYE Service and Research Center 1705 14th St. 115 Boulder, CO 80302 Phone : 303.443.4595 Toll Free...