Assessments - 4, GPA: 5
(
)
)
|
Facilidade de uso
Caution UL Notice: FMW51BC1 External Battery Charger PenCentra 130 Users: Use this battery charger with the CP021031 (FMW51BP1) battery pack only. Stylistic LT Users: Use this battery charger with the 3-cell battery pack CA54200-0502 (FMW29BP2) or 6-cell battery pack CA54200-0506 (FMW29BP1) only. Using the Battery Charger To charge your battery pack(s) in the external battery charger: 1. Connect an FPSI DC power source such as AC adapter FMWAC4A, FMWAC4B, FMWAC4C or auto adapter FMWCB2 to the DC input on the battery charger. The Power status indicator on the charger turns on indicating that power is supplied to the charger. 2. Insert the battery pack into one of the slots in the battery charger as shown in the following figure until the battery pack is firmly seated in the charger. 3. There are two status indicators on the battery charger, one for each slot. The status indicators change colors to represent different battery conditions, as noted in Table 1. Table 1: Status Indicator States Indicator Condition Status Power OFF AC Adapter not connected Green/ON AC Adapter connected Battery 1/ Battery 2 OFF No battery installed Green/ON Charge complete Amber ON Blink 1 Charging Standby (Waiting to charge) Red ON 2 Blink 1,2 Battery pack alarm Battery charger alarm 1 Blinks at rate of one second on, one second off. 2 If the battery charger indicates a fault condition with the battery pack, remove the battery pack, disconnect power to the charger, and contact your local help desk or your reseller for further assistance. Rechargeable Battery Pack Slide Connector Pins DC Input Status Indicators 1 2 Power Battery 1 Battery 2 Battery Slot 2 Battery Slot 1 Stylistic LT and PenCentra 130 are trademarks of Fujitsu Personal Systems, Inc. © 1999 Fujitsu Personal Systems, Inc. 6/99 58-0664-00A 4. When the charged battery pack is needed, remove the battery pack from the charger. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital When the battery charger is not in use, disconnect the DC power source. device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable Operational Considerations protection against harmful interference in a residential installation. This equipment Issues to consider when you use the FMW51BC1 generates, uses, and can radiate radio battery charger are discussed as follows: frequency energy and, if not installed and used in accordance with the instructions, may cause • You can insert up to two battery packs at a time harmful interference to radio communications. in the battery charger. When charging two However, there is no guarantee that interference battery packs, you can insert or remove either will not occur in a particular installation. If this battery pack independently. equipment does cause harmful interference to radio or television reception, which can be • The battery charger only charges one battery determined by turning the equipment off and on, the user is encouraged to try and correct the pack at a time. When two battery packs are interference by one or more of the following measures: inserted in the charger, the battery pack installed first is charged first. • Reorient or relocate the receiving antenna. • The battery charger will indicate a full charge level and will not begin charging the battery pack • Increase the separation between the if the battery pack charge level is 90% or higher equipment and receiver. when the battery pack is initially inserted in the • Connect the equipment into an outlet on a charger. This prevents the battery pack from circuit different from that to which the being overcharged. receiver is connected. • When you remove the battery pack from your • Consult the dealer or an experienced radio/ pen tablet, always insert a charged battery pack TV technician for help. in the pen tablet to replace the one that you removed, or apply DC power. Changes or modifications not expressly approved by Fujitsu Personal Systems, Inc., could void the user’s authority to operate the • The FMW51BP1, FMW29BP1, and FMW29BP2 equipment. battery packs use lithium ion battery cells which have no “memory effect.” You do not need to discharge or “condition” the battery pack before charging. Battery Pack Charge Time The approximate maximum amount of time needed to charge a fully discharged battery pack to the 90% level is shown in the following table. Note that when two battery packs are installed in the charger, they are charged sequentially (starting with the battery pack that is installed first). 58-0664-00A Battery Pack Approximate Charge Time 3-cell FMW51BP1 <2 hours FMW29BP2 <2 hours 6-cell FMW29BP1 <3.5 hours 2 of 2 ...