Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
11 Do not operate the UV sanitizer where aerosol (spray) products are being used or where oxygen is being administered. SAVE THESE INSTRUCTIONS A Door recess B Removable protective screen for light bulb C Removable drip tray D Power on/off button E UV clean LED F UV light bulb G Center post to attach brush head holders H Brush head holders -H1 brush head holder for Sonicare ProResults brush heads -H2 brush head holder for Oral-B Flexisoft*, Oral-B FlossAction** No brush head holder needed for Sonicare e-series brush heads. EnglisH Before first use Note:Your sanitizer may come with the UV light bulb installed. If this is the case, go on to chapter ‘Preparing for use’. 1 Placeyourfingerinthedoorrecessontheright-handsideofthesanitizerandpullopenthedoor. Removethedriptray. 3 Removetheprotectivescreenbygentlyliftingitup(1)andpullingitforward(2). 4 InstalltheUVlightbulbbysnappingitintothelampholder. Donotcrushorbreakthebulb.UVlightbulbscontainasmallamountofmercury. Note: Use only the UV light bulb supplied or a replacement UV light bulb ordered from Philips or Philips Authorized Service Centers. Note:To remove the UV light bulb, pull it out of the lamp holder. AlignthepegsontheprotectivescreenwiththeslotsinthereflectivesurfaceofthesanitizeroneithersideoftheUVlightbulb. EnglisH Insertandgentlypushdownthescreentosecureitinthesanitizer. Reattachthedriptray. Preparing for usesanitizing sonicare e-series brush heads1 Placeyourfingerinthedoorrecessontheright-handsideofthesanitizerandpullopenthedoor. PlacethebrushheadsdirectlyonthedriptraywiththebristlesfacingtheUVlightbulb. sanitizing sonicare ProResults, Oral-B Flexisoft and Oral-B FlossAction brush heads Note:This sanitizer is NOT suitable for other brush heads. 1 Placeyourfingerinthedoorrecessontheright-handsideofthesanitizerandpullopenthedoor. Removethedriptray. 3 Selecttheappropriatebrushheadholder(seechapter‘Generaldescription’). EnglisH 4 Attach the brush head onto the appropriatebrush head holder (see chapter ‘General description’). Attach the left brush head holder (L) to theleft side of the center post until it clicks intoplace. Note:The brush head holders do not fit properly when you place the right brush head holder first. Always start with the left brush head holder. Attach the right brush head holder (R) to theright side of the center post until it clicks into place. Place the drip tray back into the sanitizer. Place the brush heads onto the brush head holders with the bristles pointing towards theUV light bulb. Sanitizing brush heads of two different types If you want to sanitize brush heads of two different types, use the appropriate brush head holder for each type. 1 Select the appropriate brush head holder for each type of brush head (see chapter ‘Generaldescription’. Sonicare e-series brush heads donot require a brush head holder). Follow the instructions given under ‘SanitizingSonicare ProResults, Oral-B Flexisoft and Oral-B FlossAction brush heads’. 10 EnglisH Do not place the travel cap on the brush headduring sanitization. 1 After brushing, rinse the brush head and shakeoff excess water. Place your finger in the door recess on the right-hand side of the sanitizer and pull openthe door. 3 Put the brush heads into the sanitizer (seechapter ‘Preparing for use’). Note: Make sure the bristles of the brush head face the light bulb. 4 Close the sanitizer door. Note:The sanitizer does not work when the door is not properly closed. Put the plug in a live power outlet. Press the power on/off button to start the UVclean cycle. Note:The sanitizer is in operation when the blue light glows through the window on the front of the sanitizer and the UV clean LED flashes slowly. Note:The sanitizer needs to run for the full 10-minute UV clean cycle to get optimal results. Note:When the sanitizing cycle is complete, the UV clean LED turns solid green and the sanitizer automatically shuts off. Note:You can stop the sanitizer during the sanitizing cycle by either pressing the on/off button or by opening the door. Using the appliance EnglisH 11 Cleaning and maintenancestorage Do not clean any of the sanitizer accessories in adishwasher. Do not clean the sanitizer when the UV light bulbis hot. For optimal effectiveness, it is recommended to clean your sanitizer as follows: 1 Unplug the sanitizer. Remove the drip tray, protective screen andthe light bulb (see chapter ‘Before first use’). 3 Thoroughly rinse the brush head holders and the drip tray with warm soapy water and wipethem clean with a damp cloth. 4 Wipe the bulb, the protective screen, and allinternal and external surfaces with a damp cloth. Let all items dry before you reinstall them. Reattach the drip tray, protective screen andlight bulb (see chapter ‘Before first use’). -If you are not going to use the sanitizer for an extended period of time, unplug it from the electrical outlet, clean it and store it in a cool and dr y place away from direct sunlight. -You can use the cord-wrap feature to store the power co...