Assessments - 5, GPA: 4 ( )

Fabricante : Enviro Arquivo Tamanho: 1.39 mb Arquivo Nome : Bistro-4500-Owners-Manual.pdf Língua de Ensino:

The cart will look similar to Figure 4. There should be a small box, a large box, the aluminum axle and some packaging materials. Figure 4 The components shown in Figure 5 should be found in the larger box. Most of the stainless steel components are covered with plastic to prevent scratching the unit during assembly. This can be removed Figure 5 5 The components shown in Figure 6 should be found in the smaller box. Figure 6 ENGINE COMPONENTS: . Pre-assembled engine . (3) Flame diffusers . Warming Rack . Metal Foil Container . Utensil rack . Owner’s manual . Grill removal tool . Warranty card . Hose with pressure regulator . (8) 1.4” x 1.2” stainless steel bolts . (2) 1.4” stainless steel nuts . (8) 1.4” stainless steel lock washers When the top of the shipping box has been removed and the lid has been opened, it will look similar to Figure 7. A metal foil container is taped to the warming rack and the warming rack is taped to the windshield. All tape must be removed from inside the engine before your Bistro 4500 is started for the first time. The three flame diffusers are stacked and the rest of the components will be found in the manual bag. Figure 7 The components shown in Figure 8 should be found in the manual bag found inside the engine. Figure 8 6 SIDE BURNER COMPONENTS (OPTIONAL): . Pre-assembled side burner . (2) Shelf gussets . Cast side burner grill (2 pieces) . Side burner porcelain diffuser cap . NG Orifice . Nutdriver (used to change orifice) . (10) 1.4” x 1.2” stainless steel bolts . (4) 1.4” stainless steel nuts . (10) 1.4” stainless steel lock washers Figure 9 ROTISSERIE COMPONENTS (OPTIONAL): . Rotisserie Motor . Side mount bracket . (4) Stainless steel thread rolling screws (one extra) . Rotisserie rod (not shown) . (2) Spit forks . Spit bushing . Counter weight assembly Figure 11 Figure 10 Figure 12 7 CASTERS AND WHEELS INSTALLED ONTO CART ASSEMBLY: When the cart cabinet has been emptied the wheels and casters can be installed. Leave the cart body upside down; this will make installing the wheels and casters easier. Components Required: . Pre-assembled cart . (2) Plated caster assemblies . Aluminum axle and (2) end caps . (2) Stainless steel axle mount . (2) BBQ wheels . (14) 1.4” x 1.2” stainless steel bolts . (14) 1.4” stainless steel lock washers . (14) 1.4” stainless steel nuts Figure 14 The casters must be installed on the bottom left side of the cart body. Each caster requires four (4) bolts, four (4) lock washers, and four (4) nuts. Put the casters in place (see Figure 13 & 14) and slide the bolts through the holes in the caster brackets into the holes in the bottom of the cart body. Open cabinet doors and place a lock washer and a nut onto each bolt. Using a 1.4” socket or nut driver and a 5/32” Allen key, tighten all the nuts and bolts. The axel mounts must be installed on the right side of the cart body. Each axel mount requires three (3) bolts, three (3) lock washers, and three (3) nuts. Put the axel mounts in place with the holes for the axel closest to the bottom of the cart body (see Figure 13 & 15). Slide the bolts through the holes in the mount into the holes in the side of the cart body. Place a lock washer and a nut onto each bolt. Using a 1.4” socket or nut driver and a 5/32” Allen key tighten all the nuts and bolts. Before the wheels can be installed they must be partially assembled. Press one wheel onto an end of the axel so that approximately 1.2” (1 cm) of the axel is out past the wheel. The side with the webbing on it is to face out. A hammer or mallet may be needed to help put the wheels on the axel. Press an end cap all the way onto the end of the axel with the wheel on it; ensure the wheel is butted up against the end cap (see Figure 16). Slide the axel through the holes in both axel mounts; it may be a tight fit so turn the axel while pressing it through the holes. Press the other wheel, then the end cap, onto the free end of the axel. Figure 13 Figure 15 Figure 16 8 ENGINE INSTALLED ONTO CART ASSEMBLY: Components Required: . Rolling cart . Pre-assembled engine . (4) 1.4” x 1.2” stainless steel bolts . (4) 1.4” stainless steel lock washers . Metal Foil Container . Drip tray WARNING: Two (2) people are required to lift the engine onto the cart safely. Empty all the components (frame deflectors, manual bag, and warming tray) from inside the engine to make it lighter to lift. Turn the cart body right side up. Using two (2) people, lift the engine onto the cart. Take care to line up the manifold fitting on the bottom of the engine with its corresponding cut away on the top of the cart. Refer to Figure 17. ............................................................................................................................................................................................................................................................................................................................................ Figure 17 Attach the engine to the...

Baixe o seu

Para fazer o download, introduza 2 dígitos :