Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
2. Place the speaker into the opening and check for proper fit. Remove the speaker and replace the paper door liner previously removed. Selecting the Speaker Location 1. This is a good speaker location , but to use it, you’ll have to enlarge the existing hole 2. Check for free window crank movement 3. Check for possible braces behind selected area with window down andup 4. This is a poor location for a speaker installation; it is too low and behind driver’s hearing area Speaker Mounting Let’s assume you didn’t find a suitable opening, but you want to install the speakers in the doors. This usually means you will have to cut a speaker opening in the sub-metal (or at least enlarge an existing opening). Cutting metal is not for the timid or unqualified installer. If in doubt, proceed to your nearest garage or stereo installation center and let the “pros” do it for you. If you intend to tackle the job yourself, break out your best metal- cutting tools (no torches please); use nibblers, saws or heavy snips. You’ll need a file too. Prepare the opening as follows: -6 Cutting Door Padding 1. Use a sharp knife to cut through padding to expose speaker hole 2. Replace door panel and paper liner 128-6825 6 of 10 Piercing Speaker Mounting Holes Enlarging or Cutting a New Hole 1. Opening 1. Enlarge or cut new hole per template 2. Speaker 2. Tape 3. Pierce the speaker mounting holes 3. Template 4. Metal cutting saw 5. File hole smooth after cutting Cutting Door Padding and Piercing Speaker Mounting Holes After routing the speaker wires, perform the final installation as follows: 1. Replace door panel, window crank, etc. Press against door panel to locate speaker hole. Then, using a sharp knife or box cutter, cut out opening in padded door panel. Using an Existing Hole 2. Replace speaker in opening and pierce the three or four speaker mounting holes. Remove speaker. 1. Speaker 2. Drill 3. Drill the required speaker mounting holes -7 128-6825 7 of 10 Routing Speaker Wires 3. Place speaker into door and secure using screws (and clips, Route the speaker wires as follows: if necessary) provided with speaker. 1. Route speaker wires from stereo into door. If possible, use 4. Test the speaker. Then install grille (grille snaps over outer existing wires. If door is not equipped with grommets, drill ring of speaker frame). Repeat for remaining door. a 1/4” hole in door edge and door frame. 2. Connect wires to speaker per stereo wiring instructions. Allow enough slack between door edge and frame to fully open door. DO NOT tape wires to hinges or braces. 1 2 4 3 Routing Speaker Wires Securing Speaker and Grille 1. Door Frame 2. Kick Panel 3. Connect speaker wires to speakers 1. Mesh Grille 4. Route wires to stereo 2. Speaker mounting screws 5. Drill 1/4” hole or use existing grommets 3. Speaker 6. Door (open) 4. Grille -8 128-6825 8 of 10 Speaker Mounting Details The following illustrations define the requirements for mounting the MESH GRILLE speaker on the near and far sides of the mounting surface or inde pendent mounting board. FACTORY GRILLE SPEAKER EXISTING FACTORY HARDWARE MOUNTING SURFACE FACTORY SPEAKER REPLACEMENT APPLY BUTYL PUTTY (4 PLACES) GRILLE SHEET METAL SCREWS SPEAKER MOUNTING SURFACE SPEED CLIP TYPICAL SPEAKER INSTALLATION -9 128-6825 9 of 10 AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below. This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, accessories, or vehicle electrical systems. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s) or markings. THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY W...
Este manual também é adequado para os modelos :Speakers - Rampage Portable Speaker (112.94 kb)