Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
gETom tjp c ” <■ si- »■■■I -i-i- 5 6 7 8 9 10 11 12 13141516 17 18 19 1. Release Button - Press this button to release the shuttle unit. 2. 24 pin Shuttle Interface Connector - Used to connect the shuttle to the DTT7810FM. 3. Speakers for Shuttle Models DT102, DT85 and Dt7. 4. Power Button - To turn the DTT7810 FM (ON/OFF) 5. Volume Up I Down Button - Used to increase and decrease the volume level. 6. Channel Up I Down Button - Used to go to the next channel Up or Down. 7. Source Button - Select from the four (4) available sources. DVD > TV> AV> RADIO 8. Bass Boost Button - Used to increase the low frequency (bass) response. 9. Alarm Off Button - Used to turn off the alarm. The alarm will automatically turn off after one minute 10. Sleep Button - Used to set the DTT7810 sleep mode. The unitwill turn OFF in 15, 30, 45, 60, 90, or 120 minutes. 11. Dimmer - Used to control the brightness of the LCD display. 12. Snooze - Used to reset the alarm function for 9 minutes. 13. LCDDisplayWindow-TheLCDdisplayis usedtoshowthe Time, Sourceselected,and Radio Station. 14. IR Receiver-Allows remote control ofthe DTT7810 and the installed shuttle (DT102, Dt85orDT7). 15. Store Button - Used to set the AM/FM presets into memory. 16. Radio Tune / Clock Set - In Standby mode these buttons are used forsetting hours, minutes, and to select from 12 and 24 hour mode. - In operation mode these buttons are used for radio tuning Up and Down. 17. Clock Mode Button - Used to select the clock or alarm item to be set. 18. Recall Button - Used to recall the radio display and select preset stations. 19. AM I FM Button - Radio Band selector. (FM1, FM2 and AM) 3 Main Features Back Panel Connections 1 2 3 4 5 AV IN - The shuttle will accept an AV input through the AVjacks located on the rear of the unit. The video device could be a video game system, video camera, or other input device. •VIDEOIN-Yellow •AUDIO IN (L (-White •AUDIO IN (R)-Red 2. DC 12V- Connect the supplied AC to DC adapter to this jack. The shuttle is designed for negative ground 12V DC operation. 3. ANT - Connect the coaxial cable from an antenna or cable TV system to this jack. 4. FM IN - Connect the FM radio antenna to this jack. 5. AM IN - Connect the AM radio antenna to this jack. 4 Remote Control Operation BATTERY COVER Batterv Installation Before attempting to operate your Remote Control, install the batteries as described below. 1)Turn the Remote Control face down. Using a fingernail, lift the battery cover off. 2) Install two “AAA” batteries. Make sure that proper polarity (+ or -) is observed. 3) Align the cover tabs with the remote control and press down until the coverclicks. The remote control will operate the VDS102T and Audiovox shuttle models (DT102, DT85 or DT7) It is not a universal remote control and will not control equipment from other Remote Control Function Descriptions ON/OFF SELECT /'T'N. Cl '® ® ® ® ® ® ® ® ® QjDt •ARCHT^A /"\sEARCH RETURN REPEAT ( TV DVD RADIO TViCATV Ol 5 * Function control is available on the unit and the remote control. ** Used onlywhen Shuttle (DT102, DT85 or DT7) is installed. 1. POWER Button* Press this button to turn the DTT7810FM ON. Press the button again to turn the DTT7810FM OFF. 2. SOURCE Button* Use to select one of the four sources (DVD, TV, AV, and Radio) 3. AUTO MEMORY Button (AUTO PROGRAM Button)** When the AUTO MEMORY button is pressed, all channels are searched and channels that are detected with signals of sufficient levels are automatically stored inmemory. 4. SKIP I SEARCH Button** This button selects between SKIP ON and SKIP OFF mode. In “SKIP mode” the TV tuner will only stop on channels that are programmed into memory. In SKIP OFF mode the TV will stop on all active channels. 5. ERASE I WRITE Button** While tuned to a channel, pressing this button will store or erase the channel from memory. The word “ADD” and the stored channel numbers are displayed in “GREEN”. The word “ERASE” and the erased channel numbers are displayed in “RED”. 6. SEEK I CHANNEL UP (^) Button** Use this button to increase the TV channel number or radio station to the desired channel and to scroll upward in menu options. 7. MUTE Button Press this button to mute the audio. Pressing the button again restores the sound to the previously set level. 8. ENTER Button** Used to implement a selected setting or menu option. 9. LEFT (< ) Button** Allows the user to shift left in the menu options. -Or- SEARCHM Button** When this button is pressed radio stations are searched in descending orderand the tuner will stop on the next active channel 10. MENU Button** Allows the user to access the DVD root. 11. RETURN Button** Not used in this model. 12. TV Mode Select Button** Switches certain function keys on the remote control to TV functions. 13. DVD Mode Select button** Switches certain function keys on the remote control to DVD functions. 14. DISPLAY Button** Pres...