Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
Repeat the same procedure to restore the 12-hour standard. If the clock display flashes This is caused by a power interruption. The current time needs to be reset. If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be reset. MULTI JOG is also available instead of U and W. II 1 2 u, The unit can be turned off automatically at a specified time. Use the remote control. 1 Press SLEEP while pressing SHIFT. 2 Within 4 seconds, press < or W to specify the time until the power is turned off. Each time the button is pressed, the time changes between 5 and 240 minutes in 5-minute steps. Specified time I To check the time remaining until the power is turned off Press SLEEP once while pressing SHIFT. The remaining time is displayed for 4 seconds. To cancel the sleep timer Press SLEEP twice while pressing SHIFT so that “SLEEP OFF” appears on the display. * MULTI JOG is also available instead of U and W. 15 ENGLISH 4 Select the duration for the timer-activated periold f with 4 DOWN or -UP, then press [I set. ~ 3 6 2,4 1I A 1 P “[-----i‘ —1,2,3,4 ?\-—.——-9 —.. 1 The unit can be turned on at a specified time every day with the built-in timer. Preparation Make sure the clock is set correctly. Use the remote control. 1 Press TIMER to display 0, then press II SET within 6 seconds. O is displayed and the hour flashes. m If you press II SET after 6 seconds, another operation may start. 2 Designate the hour of the timer-on time by pressing < DOWN or > UP, then press II SET. Repeat to designate the minute of the timer-on time. After you designate the timer-on time, one of the source names flashes on the display. 3 Press FUNCTION to select a source, then press II SET. If TUNER is pressed, the band cannot be selected in this step. .g- The duration for the timer-activated period can beset between 5 and 240 minutes in 5-minute steps. G 5 Prepare the source. To listen to a CD, load the disc to be played first on tray 1. To listen to a tarJe, insert the tape into deck 1 or 2. To listen to the radio, tune in to a station. 6 Press POWER to turn the unit off after adjusting the volume and tone. O remains on the display after the power is turned off (timer standby mode). When the timer-on time is reached, the unit turns on and begins play with the selected source. The volume level is automatically set to 16 when the power is turned off with the volume level set to 17 or more, To check the specified time and source Press TIMER. The timer-on time, the selected source name and the duration for the timer-activated period are displayed for 4 seconds. To cancel timer standby mode temporarily Press TIMER re~eatedlv until ~ disaDDears on the dlSDlaV. To restore the timer standby mode, press TIMER once’ortwice to display 0. Using the unit while the timer is set You can use the unit normally after setting the timer. Before turning off the power, carry out step 5 to prepare the source, and adjust the volume and tone. Timer playback and timer recording will not begin unless thle power is turned off. Connected equipment cannot be turned on and off by the built- in timer of this unit. Use an external timer. * MULTI JOG is also available instead of 4 and >. Timer recording is applicable for TUNER and VIDEO/AUX (wi’!h an external timer) sources only. Press TIMER repeatedly until @ flashes on the display, them press II SET within 6 seconds. Carry out the steps of “SETTING THE TIMER” from step 2 and insert the tape to be recorded on into deck 2 after step 5. ENGLISH 16 CD DIGITAL OUT (OPTICAL) vIDEO/AUX SURROUND SPEAKERS Refer to the operating instructions of the connected equipment for details. . The connecting cords are not supplied. Obtain the necessary connecting cords. Consult your local Aiwa dealer for optional equipment. .-....=..,----- ?$,:--.:,’! ,= 2. ,.... . . .,.,., -.-:*N :=: : -m-7.%..-,:;:$.-’-.:-.,: -.. . .-.:’..2.:.=$ ‘~’.-:=~fl= .J”=* s -=.’”’ VIDEO/AUX JACKS This unit can input analog sound signals through these jacks. Use a cable with RCA phono plugs to connect audio equipment (turntables, LD players, MD players, VCRs, TV, etc.). Connect the red plug to the VIDEO/AUX R jack, and the white plug to the VIDEO/AUX L jack. When connecting a turntable Use an Aiwa turntable equipped with a built-in equalizer amplifier. .T”zis:.u *X:.-“ ‘,.; S.? .*.:*,%4 .-.-..-:-: .,_.L-., . y,yJ-& :;! CD DIGITAL OUT (OPTICAL) JACK This unit can output CD digital sound signals through this jack. Use an optical cable to connect digital audio equipment (DAT deck, MD recorder, etc.). Remove the dust cap @ from the CD DIGITAL OUT (OPTICAL) jack. Then, connect an optical cable plug to the CD DIGITAL OUT (OPTICAL) jack. When the CD DIGITAL OUT (OPTICAL) jack is not being used Attach the SUppllMt O’USt cap. 1 POWER To play equipment connected to the VIDEO/AUX jacks proceed as follows. 1 Press VIDEO/AUX. “VIDEO” or “AUX appears on the display. 2 Play the connected equipment. To change a source name in the ...
Este manual também é adequado para os modelos :Speakers - CX-NA303 (8.81 mb)
Speakers - NSX-A303 (8.81 mb)