Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Chamber Drive unit Main duct What is the SAW design? The SAW design features a centrally-positioned woofer drive unit, two chamber construction, and a long main duct. Through precision control of the acoustics of the two chambers, the unit can reproduce powerful ultra low frequencies without muddiness. In addition, we also included two super woofer modes designed to bring the dynamic bass sounds found in movie theaters (mode 1) and concert halls (mode 2) to your living room. Power turns on and off automatically The speakers turn on automatically when a sound signal is input and turn off when you've finished watching a program and the sound signal goes out. So you don't have to bother using the power switch every time you use the system. Getting Started Getting Started Precautions On safety • Should any solid object or liquid fall into the cabinet, unplug the speaker system and have it checked by qualified personnel before operating it any further. On power sources • Before operating the speakers, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate on the rear of the speakers. • The speakers are not disconnected from the AC power source as long as they are connected to the wall outlet, even if the speakers themselves have been turned off. • If you are not going to use the speakers for a long time, be sure to disconnect the speakers from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. • One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. • Should the AC power cord need to be changed, have it done at a qualified service shop only. On placement • Do not place the speakers near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Good ventilation is essential to prevent internal heat buildup. Place the speakers in a location with adequate air circulation, and in a way that does not block the rear ventilation holes. On cleaning • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. For the customers in the USA For detailed safety precautions, see the “IMPORTANT SAFEGUARDS” leaflet. If you have any question or problem concerning your receiver, please consult your nearest Sony dealer. Unpacking Check that you received the following items with your speaker system: • Front L/R speaker connecting cord, 3.5 m (1) • Rear speakers SS–SR151 (2) • Rear speaker connecting cords, 10 m (2) • Audio connecting cord, 1.5 m (1) • Remote commander (remote) RM–J15 (1) • Size AA (R6) batteries (2) • Speaker Stands (2) • Screws (8) Inserting batteries into the remote Insert two size AA (R6) batteries with the + and – on the battery compartment. When using the remote, point it at the remote sensor gon the left front speaker. ] ] }} When to replace batteries Under normal use, the batteries should last for about 6 months. When the remote no longer operates the speakers, replace both batteries with new ones. Notes • Do not leave the remote in an extremely hot or humid place. • Do not use a new battery with an old one. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Getting Started Getting Started Installing the Speaker Stands Be sure to install the supplied speaker stands before you use the speakers. 1 Spread a towel, or other soft cloth, over a table and lay the speakers down. 2 Align the pins on the stands with the holes on the bottom of the speakers. Speaker stand Bottom of speaker 3 Use a screw driver to fasten the stands to the bottom of the speakers with the supplied wood screws (4 for each speaker). 4 Make sure the stands are securely attached and stand the speaker upright. Choosing the Best Location To obtain high sound quality and a proper sound image from the front speakers, place the speaker with the built–in operation panel to the left of your TV and the other to the right of your TV so that the center channel tweeters angle towards the center of the room. For the best central sound image, place the left and right speakers within 8 feet of each other and equidistant from the TV. 8 feet (max) Place the rear speakers so that they fire directly across at each other about 2 to 3 feet above your listening position. 2-3 feet Getting Started Getting Started Speaker System Hookups This section describes how to connect the speaker system and how to connect your TV or VCR to the speakers. The arrow .indicates signal flow. Right rear speaker (SS-SR151) Connecting the front speakers r...