[For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. i En SUPPLIED ACCESSORIES CONNECTIONS TO YOUR AMPLIFIER SUPPLIED ACCESSORIES CONNECTIONS TO YOUR AMPLIFIER Before making connections, make sure that the amplifier is switched off. Fastener . 4 PLACING THE SPEAKERS Place the speaker on a TV rack or other stable surface. To prevent the speaker from falling down, attach the fasteners provided in each corner of the speaker's underside. Front Surround Surround back Subwoofer NS-C700 Fastener Notes • Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength. • Thoroughly wipe clean the surface where the fasteners are to be attached. Note that adhesive strength is weakened if the surface is dirty, oily or wet, and that this may cause the center speaker to drop. • Placing this unit too close to a TV set might impair picture color or create a buzzing noise. Should be happen, move the speaker away (more than 20 cm (7-7/8”)) from the TV set. • To avoid accidents resulting from tripping over loose speaker cables, fix them to the floor. – CENTER + Loosen Black (–) Insulation coating Tighten Red (+) Bare wire NS-C700 Amplifier or Receiver • Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of the amplifier (or receiver) with the speaker cable. • Connect the (+) terminals on the amplifier (or receiver) to the (+) terminal of each speaker, making sure to confirm the color- coded wire of the cable at each end. Use the other wire of the cable to connect the (–) terminals of the components. • Connect the speaker to the center terminals of your amplifier, making sure not to reverse the polarity (+, –). If the speaker is connected with reversed polarity, the sound will be unnatural and lack bass. English 1 En ¦¦ 1 Loosen the knob. 2 Remove 10 mm (3/8”) of insulation from each end of the cables, and twist the exposed conductors together neatly and tightly, as shown below. 10 mm (3/8 ”) Good No Good 3 Insert the bare wire. 4 Tighten the knob and secure the cables. Test the firmness of the connection by pulling lightly on the cables at the terminal. Notes • Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both. • Do not insert the insulation into the hole. Sound may not be produced. ¦When using a banana plug Note Do not take off this cover unless using a banana plug. Banana plug Cover 1 Tighten the terminal knob. 2 Remove the cover by pulling it toward you. 3 Simply insert the banana plug into the terminal. Note Use a suitable instrument to remove the cover. Removing it with your bare hands may hurt your fingertips. ATTACHING THE FRONT COVER The speaker and the front cover are packed separately. To attach the front cover, line up the projections (magnets) on the reverse side of the front cover with their corresponding screw heads on the speaker. Notes • When removing the cover, be careful that you don’t touch the drive units, and don’t exert excessive force with any tools. • There are magnets on the reverse side of the front cover. Do not place a front cover close to objects that might be affected by magnets, such as TV, clock, magnetic card, diskette, etc, after removing it. 2 En SPECIFICATIONS SPECIFICATIONS DC diaphragm Impedance............................................................................... 6 . Frequency Response ............................ 60 Hz to 50 kHz (-10 dB) 100 kHz (-30 dB) Nominal Input Power........................................................... 40 W Maximum Input Power ...................................................... 160 W Sensitivity ........................................................... 89 dB/2.83 V/m Crossover Frequency .......................................................... 5 kHz Dimensions (W . H . D)............................ 500 . 170 . 170 mm (19-11/16” . 6-11/16” . 6-11/16”) Weight.............................................................7 kg (15 lbs. 7 oz.) • Specifications subject to change without notice due to product improvements. • Care should be taken not to exceed the input power values noted above. • A speaker cable is not included with this model. Taking care of the speaker When you wipe this unit, do not use chemical solvents (e.g., alcohol or thinners, etc.): this might damage the finish. Use a clean, dry cloth. For difficult soils, dampen a soft cloth in detergent diluted with water, wring it out, and then wipe with the cloth. Limited Guarantee for European Economic Area (EEA) and Switzerland Thank you for having chosen a Yamaha product. In the unlik...

Este manual também é adequado para os modelos :
- ()