Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
2 Insert the bare wires. 3 Release your finger from the tab to allow it to lock securely on the cable’s wire end. 4 Test the firmness of the connection by pulling lightly on the cable at the terminal. + 1 2 – Notes • Do not let the bare speaker wires touch each other, because this could damage the subwoofer or the amplifier, or both of them. • For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the subwoofer or the speakers, or both of them. • Make sure that the + and – polarity markings of the speaker terminals are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. Plug in the subwoofer to the AC outlet After all connections are completed, plug in the subwoofer and other audio/video components to the AC outlet. OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER INPUT 2 PHASE AU TO STANDBY HIG H VO LTAGE SELECTOR POWER ON OFF 220V-240V 110V-120V LOW OFF NORM REV /MONOL R To AC outlet CONTROLS AND THEIR FUNCTIONS Advanced215634Control panel CONTROLS AND THEIR FUNCTIONS Advanced215634Control panel Top Front panel OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER INPUT 2 PHASE AUTO STANDBY HIGH VO LTA G E SELECTOR POWER ON OFF 220V-240V 110V-120V LOW OFF NORM REV /MONOL R POWER ON OFF AUTO STANDBY HIGH LOW OFF OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER INPUT 2 PHASE NORM REV /MONOL R VOLTAGE SELECTOR 220V-240V 110V-120V 78AB09CRear panel(General model) 1 Power indicator Lights up in green while the subwoofer is on. Lights up in red while the subwoofer is set in the standby mode by the operation of AUTO STANDBY function. (Refer to page 11 of “AUTO STANDBY FUNCTION” .) Goes off when the subwoofer is set in the standby mode by pressing the STANDBY/ON button. 2 STANDBY/ON button Press this button to turn on the power when the POWER switch is set in the ON position. (The power indicator lights up in green.) Press again to set the subwoofer in the standby mode. (The power indicator goes off.) Standby mode The subwoofer is still using a small amount of power in this mode. 3 B.A.S.S. (Bass Action Selector System) button When this button is pressed in to the MUSIC position, the bass sound in audio software is well reproduced. By pressing the button again so that it pops out at the MOVIE position, the bass sound in video software is well reproduced. 4 HIGH CUT FILTER button ON: Enables the HIGH CUT control setting (5). PASS: Simplifies the signal path to reduce sound deterioration. (Choose this setting if your amplifier has LFE or subwoofer output terminals.) PASS ON English 9 CONTROLS AND THEIR FUNCTIONS 5 HIGH CUT control Adjusts the high frequency cut off point. Frequencies higher than the frequency selected by this control are all cut off (and no output). * One graduation of this control represents 10 Hz. 6 VOLUME control Adjusts the volume level. Turn the control clockwise to increase the volume, and counterclockwise to decrease the volume. 7 POWER switch Normally, set this switch to the ON position to use the subwoofer. In this state, you can turn on the subwoofer or turn the subwoofer into the standby mode by pressing the STANDBY/ON button. Set this switch to the OFF position to completely cut off the subwoofer’s power supply from the AC line. 8 AUTO STANDBY (HIGH/LOW/OFF) switch This switch is originally set to the OFF position. By setting this switch to the HIGH or LOW position, the subwoofer’s AUTO STANDBY function operates as described on page 11. If you do not need this function, leave this switch in the OFF position. * Make sure to change the setting of this switch only when the subwoofer is set in the standby mode by pressing the STANDBY/ON button. 9 OUTPUT (TO SPEAKERS) terminals Can be used for connecting to the front speakers. Signals from the INPUT1 terminals are sent to these terminals. (Refer to page 7 of “CONNECTIONS” for details.) 0 INPUT1 (FROM AMPLIFIER) terminals Used to connect the subwoofer with the speaker terminals of the amplifier. (Refer to pages 6 and 7 of “CONNECTIONS” for details.) A INPUT2 terminals Used to input line level signals from the amplifier. (Refer to pages 4 and 5 of “CONNECTIONS” for details.) B PHASE switch Normally this switch is to be set to the REV (reverse) position. However, according to your speaker systems or the listening condition, there may be a case when better sound quality is obtained by setting this switch to the NORM (normal) position. Select the better position by monitoring the sound. C VOLTAGE SELECTOR switch (Asia and General models only) If the preset setting of the switch is incorrect, set the switch to the proper voltage (110-120/220-240V) of your area. Consult your dealer if you are unsure of the correct setting. WARNING Be sure to unplug the subwoofer before setting the VOLTAGE SELECTOR switch correctly. Note When both @INPUT1 and AINPUT2 terminals of the subwoofer are connected with the amplifi...