Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
(continued) 5EN 1/04–05_WSA10.11EN 3-810-424-12 (1) Getting Started Getting Started Connecting to an amplifier with a single set of speaker terminals If your amplifier is equipped with a single set of speaker terminals, connect the woofer to the amplifier, and then connect the front speakers to the woofer. What cords will I need? Speaker cord (supplied) (1 for each speaker) Twist the stripped ends of the cord about 2/3 inch (15 mm). Be sure to match the speaker cord to the appropriate terminal on the componentes: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass. It is useful to decide that the speaker cord marked with a line is always the positive (+) and should be connected to the positive (+) terminal to avoid any improper connections. Hookups 1 Connect the woofer to the amplifier. Connect the INPUT 2 terminals of the woofer to the amplifier’s speaker terminals with the speaker cords. Be sure to connect both L and R channels. .: signal flow Amplifier SPEAKER INPUT 2 + – R +– L R+ – L+ – This woofer 2 Connect the front speakers to the woofer. Connect the speakers to the speaker terminals of the woofer. This woofer }] SPEAKER + –R +– L }] Front Speaker (R) Front Speaker (L) Connecting to an amplifier with double(A+B) sets of speaker terminals If your amplifier has double(A+B) sets of speaker terminals, connect both the woofer and the front speakers to the amplifier. What cords will I need? Speaker cord (supplied) (1 for each speaker) Twist the stripped ends of the cord about 2/3 inch (15 mm). Hookups 1 Connect the front speakers to the amplifier. Connect the speakers to your amplifier’s speaker terminals (A). Amplifier SPEAKER A +R– +L– Front Front Speaker (R) Speaker (L) }] }] 2 Connect the woofer to the amplifier. Connect the INPUT 2 terminals of the woofer to the amplifier’s speaker terminals (B) using speaker cords (supplied). Amplifier INPUT 2 + – R +– L SPEAKER B R+ – L+ – This woofer When using the double (A +B) sets of speakers, make sure that you select the “A +B” position with your amplifier. Note When you are using speaker terminal (A) only (front speaker only) or when the power of the amplifier is turned off, turn down the volume or turn off the power of the woofer otherwise, hum noise may be heard. 6EN 1/06-07_WSA10.11EN 3-810-424-12 (1) Getting Started Getting Started Connecting to an amplifier with a special jack for a super woofer If your amplifier has a special jack for a super woofer (like a MONO OUT jack, MIX OUT jack, SUB WOOFER jack or SUPER WOOFER jack), connect the INPUT 1 jack of the woofer to one of those jacks. What cords will I need? Audio connecting cord (supplied) (1) Hookups Connect the INPUT 1 jack of the woofer to one of special jack of the amplifier with the supplied audio connecting cord. Amplifier This woofer INPUT 1 MONO OUT Note If the output level of your amplifier is not large enough, the sound may not be loud enough. In this case, connect the speaker terminals of the amplifier directly to the INPUT2 terminals of the woofer. Setting the VOLTAGE SELECTOR (Not provided on European, North American and Malaysian models) Check that the VOLTAGE SELECTOR on the rear panel of the deck is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to a wall outlet. 220 - 240 V 110 - 120 V Connecting the AC power cord Connect the AC power cord from the woofer and from your amplifier to a wall outlet. 7EN 1/06-07_WSA10.11EN 3-810-424-12 (1) Basic Operations Basic Operations Listening to the Sound S MIN MAX 50Hz 200Hz .NORMAL .REVERSE POWER LEVEL CUT OFF FREQ PHASE 2 Note Never set the amplifier’s tone control (BASS, TREBLE, etc.) or the equalizer output to a high level or input sinewaves of 20 Hz to 50 Hz recorded on a commercially- available test disk or special sound (bass sound of electronic musical instrument, pop noise of analog disc turntable, sound with abnormally enhanced bass, etc.) in a high level to this unit. These actions may cause damage to the speakers. When a special disc containing abnormally enhanced bass is played, noise may be output in addition to the original sound. In such a case, decrease the sound level. 1 1 Turn on the amplifier and select the program source. 2 2 Press POWER. The woofer turns on and the POWER indicator lights up in green. 3 3 Play the program source. Adjust the VOLUME so that sound from front speakers is not distorted. If it is distorted, the sound from the woofer will also be distorted. To turn off the power Press POWER to release the switch. If you hear noise when you turn off the woofer, turn down the woofer volume, or turn off the amplifier before turning off the woofer. 8EN 1/08-09_SAW10.EN 3-810-424-12 (1) Basic Operations Basic Operations Adjusting the Sound You can adjust the woofer to suit the sound of your front speakers. Reinforcing the bass sound gives you a greater sense of atmosphere. LEVEL CUT OFF F...
Este manual também é adequado para os modelos :Speakers - SA-W10 (156.17 kb)
Speakers - SA-W10H (156.15 kb)