Log:
Assessments - 3, GPA: 3.7 ( )

Instruções de Operação Kenwood, Modelo KDC-MP735U

Fabricante : Kenwood
Arquivo Tamanho: 1.21 mb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



por este dispositivo também tem outras instruções :

Facilidade de uso


• G-Graphic display Displays the condition of G in horizontal direction (e.g; when turning the curve) by the graphic. • G-Meter display (Graphic) Displays the maximum value of acceleration G, right direction G, and left direction G by the numerical value. • G-Meter display (Text) The maximum value of acceleration G, right direction G, and left direction G is displayed by the numerical value. The value of G is only the reference, so is different from the actual value. • G-Counter display Adds the point of the acceleration level. The point is determined after a lapse of 1 hr drive or at power off (ACC Off ), and then it will be displayed by the graph. Furthermore, the G-Counter displays the average of the past data by the line. (The scale of graph is determined along with the largest point among the past 10 data.) • The value of G-Meter display and G-Counter display can be reset by (page 17). 3 Exit G-Analyzer display selection mode Press the Control knob. English | 15 General features Display Type F G-Analyzer Stop Watch The control of stop watch can be started by G- Analyzer function. ¤ • Do not use G-Analyzer stop watch on the Public roads. 1 Enter G-Analyzer Stop Watch mode Using the Control knob, select "DISP" > "GMA" > "STOP.W". For the operation method, refer to (page 10). "STOP WATCH" is displayed. 2 Make the counter ready Press the Control knob. "Ready" is displayed. 3 Start Count When G in the vertical direction is detected during the travel, the count automatically starts. "Running" is displayed. . • You can also start the counter by pressing the Control knob. 4 Stop Count Press the Control knob. "Stop" is displayed. . • The control will start again when you accelerate or press the Control knob. Do the operation after step2. When you Reset the Count (While "Stop" is displayed) Press the Control knob for at least 1 second. . • You can reset of count when the count is stopped. 5 Exit G-Analyzer Stop Watch mode Press the [FNC] button. . • When Power off (ex; ACC OFF) while counting, the value of 1 second or less will be "00". Display Type F G-Analyzer Horsepower Analysis This measures the horsepower and displays graph and max power. It automatically saves the highest record. ¤ • Do not use G-Analyzer Horsepower Analysis on the Public roads. • Do not use this product in any way that prevents you from driving safely. • Follow all driving laws and use common sense when using this product. . • Before alternating G-Analyzer Horsepower Analysis, you are required to setup (page 18) and (page 18). 1 Enter G-Analyzer Horsepower Analysis mode Using the Control knob, select "DISP" > "GMA" > "HP". For the operation method, refer to (page 10). "HORSEPOWER" is displayed. Previous max power and record are displayed. 2 Begin measurement Press the Control knob. "Ready" is displayed. 3 Start the car "Measure" is displayed. After 15 seconds of measurement, the result is displayed. Display the result The graph shows the variation in horsepower between 0.1 to 15.0 seconds. The maximum power is displayed in red and the markings provided at intervals of 5 seconds are displayed in blue. ¤ • Pressing the Control knob also begins the measurement. To prevent danger, push the control knob before starting the car. 4 To display the maximum power in the section Push the Control knob towards right or left. Each time you push the Control knob, the maximum power in the section is displayed. 5 Exit G-Analyzer Horsepower Analysis mode Press the [FNC] button. 16 | English . • Like your vehicle’s speedometer, G-Analyzer is no more than a measuring function. The HP or G value measured by this unit may not be completely accurate due to its simplified method of measurement. The G-Analyzer is only for reference and should not be used to confirm the horsepower specifications of your vehicle. • Measuring after starting the car lowers the accuracy. • The record will not be renewed if the measurement is discontinued. • The graph’s scale adjusts automatically to the horsepower value. • The value of max power and record can be reset by (page 17). Display Type F G-Analyzer Reset Resets the value of G-Meter, G-Counter and G- Analyzer Horsepower Analysis. 1 Enter G-Analyzer Reset mode Using the Control knob, select "DISP" > "GMA" > "RESET". For the operation method, refer to (page 10). "G-RESET" is displayed. 2 Select the Reset item Turn the Control knob. Display Setting "Meter Reset" Reset the value of G-Meter. "Power Reset" Reset the value of G-Analyzer Horsepower Analysis. "Counter Reset" Reset the value of G-Counter. 3 Determine the item you want to reset Press the Control knob. 4 Reset the value Select "YES" using the Control knob. "Reset OK" is displayed. 5 Exit G-Analyzer Reset mode Press the [FNC] button. Display Type F G-Counter Level seting Calibrating G-Point. Setti...

Este manual também é adequado para os modelos :
Unidade - KDC-MP635 (1.21 mb)
Unidade - KDC-X791 (1.21 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias