However, the following control methods of the function for this unit may be differed from the Instruction manual; therefore, refer to the following supplemental instruction. 1. Select the preset band for Auto Ensemble Memory Entry. 2. Press the [AME] button for at least 2 seconds. Open Auto Ensemble Memory Entry. After storing in the memory finishes, the number of the pre-set buttons and the ensemble label are displayed. and in At the operation to press [DISP] button, use [TI] button instead. This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State. Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems) Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. 6 | English General features SRCB.BOOST ATT VOL FM AM Release button Control knob Clock display BOOST indicator Power Turning ON the Power Press the [SRC] button. . • When the power is ON, the (page 20) is displayed as "CODE ON" or "CODE OFF". Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUNER" CD "CD" External disc (Optional accessory) "CD CH" Auxiliary input "AUX" Auxiliary input (Optional accessory) "AUX EXT" Standby (Illumination only mode) "STANDBY" ATT indicator . • This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle's battery. The time until full power OFF can be set in (page 25). Volume Increasing Volume Turn the [VOL] knob clockwise. Decreasing Volume Turn the [VOL] knob counterclockwise. English | 7 General features Attenuator Turning the volume down quickly. Press the [ATT] button. Each time you press the button, the Attenuator turns ON and OFF. When the Attenuator is ON, the "ATT" indicator blinks. Audio Control 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Control mode Press the [VOL] knob. 3 Select the Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Adjust the Audio item Turn the [VOL] knob. Adjustment Item Display Range Subwoofer level "SW L" –15 — +15 System Q "NATURAL"/"ROCK"/ Natural/Rock/ "POPS"/"EASY"/"TOP40"/ Pops/Easy/Top 40/ "JAZZ" Jazz Bass level "BAS L" –8 — +8 Middle level "MID L" –8 — +8 Treble level "TRE L" –8 — +8 Balance "BAL" Left 15 — Right 15 Fader "FAD" Rear 15 — Front 15 Exit Audio Control mode (Volume control mode) . About System Q • You can recall the best sound setting preset for different types of music. • Change each setting value with the (page 9). First, select the speaker type with the Speaker setting. • "USER": The ranges selected lastly for Bass level, Middle level, and Treble level are recalled automatically. 5 Exit Audio Control mode Press any button. Press a button other than the [VOL] knob and [ATT] button. Audio Setup Setting the Sound system, such as Volume offset. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Adjust the Audio setup item Turn the [VOL] knob. Adjustment Item Display Range Low Pass Filter "LPF" 80/120/160/Through Hz Volume offset "V-OFF" –8 — ±0 (AUX : –8 — +8) . • Volume offset: Sets each source’s volume as a difference from the basic volume. 5 Exit Audio Setup mode Press the [VOL] knob for at least 1 second. Bass Boost Bass sound can be enhanced by one-touch operatin. Press the [B.BOOST] button. When you press the button once, the current Bass Boost setting is displayed. Each time you press the button, the Bass Boost setting alternates. Setting Display Bass Boost 1 "BB-L L1" Bass Boost 2 "BB-L L2" Bass Boost off "BB-L OFF" 8 | English Speaker Setting Fine-tuning so...
)
