Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Note: If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. 5 Connection diagram Notes: - In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. - Prohibit to make the conductors of auto antenna and ground touch with each other. - For your driving safety, please link your brake detecting wire with low power level, and keep it controlled by manual brake switch. Wire should be high power level and the unit cannot play DVD or VCD disc. A caution phrase will be displayed on the screen. 6 Panel controls Front panel 1. PREV/NEXT buttons 2. APS/PLAY/PAUSE button 3. TA button 4. AF button 5. PTY button 6. SRC/PWR button 7. MENU button 8. LCD display 9. EJECT button 10. BAND button 11. ADJ button 12. USB slot 13. VOL/ENTER knob/cursor RIGHT/UP/DOWN buttons 14. REL button 15. IR sensor 12 13 Inner panel The front panel of this unit can be opened to show the inner panel with disk slot. Press EJECT button to open the front panel panel. To unload the disk press EJECT button again. Note: Operating with the panel, if you do not use the unit for about 5 seconds, the panel goes back to its initial position. 8 Remote control 1. PWR button 2. SUB-T button 3. DI+/- buttons (OPTION) 4. +/-/PREV/NEXT/SEL buttons 5. CLK button 6. N/P/ANGLE (option) button 7. PLAY/PAUSE button 8. R/L/LANGUAGE button 9. RIGHT/LEFT/UP/DOWN cursor buttons/ENTER button 10. OSD button 11. SETUP button 12. Number buttons 13. AF button 14. TA button 15. PTY button 16. GOTO button 17. TITLE/PBC button 18. STOP button 19. EQ button 20. ST/RPT button 21. APS/PRG button 22. BAND/RDM button 23. MUTE button 24. SOURCE button Loading and replacing the battery Use one lithium battery (CR2025). Insert the battery with + and - poles aligned properly 9 13 14 15 General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press EJECT button, then press the RESET button to restore the unit to the original factory settings. Power button Press the SRC/PWR button on the front panel or PWR on the RC to switch the unit on. Press it again to switch the unit off. Volume control Rotate VOL knob clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. Audio settings adjustment Press MENU button shortly on the panel to enter the Menu, choose AUDIO and using UP/DOWN buttons select the mode: BASS => TREBLE => BALANCE => FADER. With LEFT/RIGHT buttons adjust each mode. - BASS/TREBLE:-7, -6, -5,......, 0, +1, +2,......+ 5, +7 - BALANCE: L07,......,R07 - FADER: L07,......,R07 Note: Adjustments to Bass and Treble will override any preset EQ (Preset Equalizer Curves). In each mode, the waiting time is about 5 seconds, and the waiting time is over, it returns to the last display mode of radio or disc playback mode. Mode selection Press the SRC/PWR button on the panel or the SOURCE button on the RC to select the mode: RADIO => USB = > SD => DVD =>TV => AUX. Mute function Press the MUTE button on the RC to cancel the sound. Press again to resume. Equalizer setting Press EQ button on the RC repeatedly to select EQ mode: NORM => ROCK => JAZZ => CLAS => POP or enter the EQ mode through the Menu setting (Audio Mode settings), press MENU button on the panel. 10 Clock display Use Menu settings (System Mode) to show the clock indication oh the display or enter clock adjustment. With LEFT/RIGHT buttons choose hours/minutes, with UP/DOWN set the right time. CLK button The display will show time after you press CLK button, the time is provided by RDS function (option). 11 Radio operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. BAND selection Press the BAND button on the panel or on the RC repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1, AM2. Auto/Manual tuning - Press and hold PREV/NEXT buttons on the panel or on the RC to choose either manual or auto search. - You also may refer to manual search using LEFT/RIGHT buttons. - Use UP/DOWN buttons on the panel to select the station that has already been stored. Auto memory store Select a band. Press APS/PLAY/PAUSE button on the panel or APS button on the RC and hold for 2 seconds to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of t...