Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
DO NOT INSTALL THE UNIT TO HIGH LEVELS OF HUMIDITY, MOISTURE OR DUST. Doing so can result in electric shock or product failure SIR-ECL2nt Installation Guide CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return the unit to your authorized retailer or nearest service center for repairing. INSTALL THE WIRING SO THAT IT IS NOT CRIMPED OR PINCHED BY SCREWS OR SHARP METAL EDGES. Route the cables away from moving parts or sharp pointed edges. This will prevent crimping and damage to the wiring. If the wiring must pass through a metal hole, be sure to use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole. USE THE SPECIFIED ACCESSORY PARTS AND INSTALL THE PRODUCT SECURELY. Be sure to use only the specified accessory parts. Use of nonspecified parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose, resulting in hazards or product failure. USE CAUTION IF YOU NEED TO DISCONNECT THE BATTERY TERMINAL. Please consult the vehicle’s owner’s manual or a service technician prior to removing the battery positive or ground connection, as it may cause damage to the vehicle’s electrical system or require reprogramming of the vehicle’s computer controlled devices. SIR-ECL2nt Installation Guide Installing the Antenna The antenna includes a plastic cable cover/ tail which covers the exposed antenna cable and keeps it attached securely to vehicle roof. The tail also helps position the antenna the proper distance from the rear window, sunroof or rear hatch. To attach the cover/tail: 1. Once you have determined the proper mounting location (see the next section), clean the area with the supplied alcohol swab. 2. Connect the antenna cover/tail to the antenna cable, making sure that the strain-relief on the antenna seats into the cover/tail groove. Route the cable through the wire channel in the cover/ tail. Installation It is recommended that prior to starting the installation, you read completely this installation manual and follow the guidelines listed below: Consider the mounting location carefully. You should make sure that you avoid the following: • Any location where the tuner is exposed to moisture. • Any location where the tuner is exposed to extreme heat. • Any location that would interfere with moving parts on the vehicle or interfere with driving. Mounting the SIR-ECL2nt tuner Be sure that you find a location that is flat and has clearance above the tuner to prevent any damage, as well as allow for ventilation. Do not install the tuner under the carpet or in a small enclosed area without proper ventilation. Doing so can result in damage to the tuner or the vehicle. Use the supplied screws to securely fasten the unit. Antenna (Underside) Adhesive Strips Cable Cover/Tail Antenna Cable 3. Remove the protective tape from the adhesive and carefully position the antenna with cover/tail and apply pressure to secure it to the vehicle. Caution: Antenna If you are attaching the tuner directly to the vehicle’s chassis, be sure that you check to make sure the area behind the tuner is free from moving parts, fuel or brake lines, wire harnesses or any other items which may get damaged by drilling a mounting hole or from the screws. Cable Cover/Tail Vehicle SIR-ECL2nt Installation Guide Optimum Antenna Mounting Locations The optimum location to mount the antenna is on the roof of the vehicle. It is important to avoid any obstruction that will block the satellite signal, such as a roof rack. For convertible vehicles, install the antenna on the trunk lid as shown. • Place the antenna on a metal surface of your vehicle at least 12” x 12”, and at least 6” from a window. (Use the antenna cover/tail as a guide for the proper distance from the rear window.) • The antenna’s magnet will secure it to the metal surface. The adhesive that is attached to the antenna cover/tail will secure the cable to the vehicle. Before routing the antenna cable, confirm that the antenna is mounted in a suitable location. • Route the cable from the antenna to the vehicle’s interior by tucking it underneath the rubber molding around the rear window, if possible. • Route the cable from the lowest point of the rear window into the trunk. Take advantage of any existing cable channels or wiring conduits. • For SUVs, minivans and five-door vehicles, bring the cable into the vehicle under the rubber molding of the tailgate, and continue under the interior trim. • From the trunk, carefully route the cable to the location of the SIR-ECL2nt and plug the SMB connector into the tuner. Sedan/Coupe SUV/Mini-Van Truck Convertible (only) Caution: • Do not pull the wire across sharp edges that could damage it. • Keep the wire away from areas where it could become tangled in the driver’s and p...