Log:
Assessments - 3, GPA: 3.7 ( )

Instruções de Operação AT&T, Modelo 1715

Fabricante : AT&T
Arquivo Tamanho: 160.85 kb
Arquivo Nome : 93ecd52d-f798-6a64-e9f4-5f1d45f1b5fd.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Part 2 © 1998 Philips Consumer Communication L.P. All rights reserved. Printed in Mexico. 848230124 Issue 1AT&T IN CASE OF DIFFICULTY If this answering system does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 722-9125. Message Window Is Blank • Make sure the power cord is securely connected to both the answering system and an electrical outlet not controlled by a wall switch. ! Use only the power cord supplied with this product. For a replacement, call 1 800 722-9125. • Press O to make sure the system is on. Messages Are Incomplete • The system can accept messages up to 3 minutes long. If a caller leaves a very long message, part of it might be lost when the system disconnects the call after 3 minutes. • If the caller pauses for more than 7 seconds, the system stops recording and disconnects the call. • If the system’s memory fills up during a message, the system stops recording and disconnects the call. System Does Not Answer After Correct Number Of Rings • If the Toll Saver feature is in operation, the number of rings changes from four to two when you have new messages waiting. • In some cases, the system might be affected by the ringing system used by the local telephone company. • If the system’s memory is full, or the system is off, the system answers after 10 rings. System Does Not Respond To Remote Commands • Make sure you are calling from a touch tone phone. When you dial a number, you should hear tones. If you hear clicks instead, the phone is not a touch tone telephone. • The answering system may not detect the Remote Access Code while your announcement is playing. Try waiting until the announcement is over before entering the code. • There may be noise interference on the phone line you are using. Press dial buttons firmly. • Make sure you are entering your Remote Access Code correctly. • You might be calling from a phone that sends tones too short for your answering system to detect. Power Failure Recovery If the system is disconnected from AC power it will not operate. Your announcement and messages are retained in memory during a power failure, but you will need to reset the clock. INSTALLATION 1 Connect the line cord. Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system. Plug the other end into a phone wall jack. 2 Connect the telephone. NOTE: If you do not want to connect a telephone, skip to Step 3. Plug the line cord from the telephone into the jack labeled TEL SET on the back of the system. 3 Connect the power cord. Plug the power cord into the jack labeled POWER and into an electrical outlet not controlled by a wall switch. Fit the power cord behind the strain relief tab. The Message Window flashes CL to indicate that you need to set the clock. ! Use only the power cord supplied with this product. If you need a replacement, call 1 800 722-9125. OPERATION Record and hear outgoing Set and hear time/day announcement Leave a message Displays number of messages, other indicators Use with other buttons to change settings Turn system on or off Delete all or selected messages Stop message playback Repeat all or part of a message Microphone Play messages Select number of times line rings before system answers Adjust volume Skip all or part of a message Set and hear Remote Access and Priority Calling Codes 5 To change the hour setting, hold down Setting the Clock / or ? until the correct You’ll need to set the clock so that it can record hour is announced. Then release the the day and time that each message is received. button. 1 Press and release g. The Message 6 Press and release C. The current Window displays CH. minutes setting is announced. 2 Press and release C. The current day 7 To change the minutes setting, hold setting is announced. down / or ? until the 3 To change the day setting, hold down correct minutes setting is announced. / or ? until the correct Then release the button. day is announced. Then release the 8 Press and release C. The new day button. and time are announced. 4 Press and release C. The current hour setting is announced. To check the clock, press and release C. OPERATION Recording Your Announcement Before using this answering system, you should record the announcement (up to 3 minutes long) that callers will hear when the system answers a call. If you choose not to record an announcement, the system answers with a prerecorded announcement: “Hello. Please leave a message after the tone.” 1 Press and release g. The Message Window displays CH. 2 Press and release A. The system beeps. Speak toward the microphone normally, from about 9 inches away. While you are recording, the Message Window displays the elapsed time of your recording. 3 Press S when you are finished. The system automatically plays back your announcement. To review your announcement, press and release A. Turning the System On/Off Use O to turn the system on and off. When the system is off, the Message Window is bl...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias