Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Carson MANUFACTURING COMPANY, INC. CARSON MANUFACTURING CO., INC. 5451 NORTH RURAL STREET INDIANAPOLIS, IN 46220 (888) 577 6877 TECHNICAL BULLETIN SA400 SA400SA400 RADIO RADIORADIO SIREN SIRENSIREN PA PAPA HORN HORNHORN VOL VOLVOL MAN MANMANWAIL WAILWAILYELP YELPYELP ON ONON OFF OFFOFF PHASER PHASERPHASER INSTALLATION AND OPERATING MANUAL SA-400-83 14V SA-400-83 28V SA-400-83 PG (Positive GND) Sound Hazard -Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) TB0324B Page 1 of 7 10/18/03 SA-400-83 SPECIFICATIONS INPUT POWER: 11-16 Volts DC, 8 Amps DC per Speaker (SA-400-83 14,PG) 22-32 Volts DC, 4 Amps DC per Speaker (SA-400-83 28) SIREN MODE OUTPUT POWER: 15 VDC input, 100W speaker(s) (SA-400-83 14,PG) 30 VDC input, 100W speaker(s) (SA-400-83 28) One speaker - 105 Watts RMS Two speakers - 180 Watts RMS AUDIO MODE OUTPUT POWER: 14 VDC input, 100W speaker(s) (SA-400-83 14,PG) 28 VDC input, 100W speaker(s) (SA-400-83 28) One speaker - 40 Watts RMS Two speakers - 80 Watts RMS SIREN FREQUENCY: 660Hz - 1325Hz Nominal CYCLE RATES: WAIL - 14 cycles/min YELP - 190 cycles/min PHASER - 15 cycles/sec AUDIO RESPONSE: 200Hz - 10KHz +/-3db Harmonic Distortion Less than 3% @ 1KHz (SA-400-83 14,PG) Harmonic Distortion Less than 7% @ 1KHz (SA-400-83 28) RADIO INPUT SENSITIVITY: 0.75VAC Input Min. for 40 Watts RMS Output (1 spkr) OPERATING TEMPERATURE: -15° F to +140° F SIZE: 6-1/8" Wide X 2-1/2" High X 5-3/8" Deep WEIGHT: 4 pounds NIGHT VISIBILITY: Backlit front control panel when power is on PROTECTION: High Voltage – Siren output stops with input voltage above highest rating Stops high output power from blowing speaker Reverse Polarity - Fuse blows when power is wired backwards Shorted Output – Fuse blows if speaker shorts (a common problem) NOTICE Due to continuous product improvements, we must reserve the right to change any specifications and information, contained in this manual at any time without notice. Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Carson Manufacturing Co., Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual. TB0324B Page 2 of 7 10/18/03 INSTALLATION Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before installing the unit. Failure to follow these instructions can cause serious damage to the unit or vehicle and may void warranties. SAFETY PRECAUTIONS For the safety of the installer, vehicle operator, passengers and the community please observe the following safety precautions. Failure to follow all safety precautions and instructions may result in property damage, injury or death. Qualifications -The installer must have a firm knowledge of basic electricity, vehicle electrical systems and emergency equipment. Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) Mounting -Mount the unit for easy access by the vehicle operator. DO NOT mount in air bag deployment area. Assure clearances before drilling in vehicle. To prevent internal damage mounting bolts must not enter case more than 1/4". Wiring -Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to vehicle battery. Testing -Test all siren functions after installation to assure proper operation. Test vehicle operation to assure no damage to vehicle. Keep These Instructions - Keep these instructions in the vehicle or other safe place for future reference. Advise the vehicle operator of the location. MOUNTING The mounting bracket supplied can be installed above or below the unit. Choose a mounting location convenient to the operator and away from any air bag deployment areas. Inspect behind mounting area for clearance. Assure adequate ventilation to prevent overheating. Consider wire routing and access to connections, as well as microphone bracket placement. Install mounting bracket to vehicle using 1/4" hardware (not supplied). If mounting in a rack or console, make sure that mounting bolts do not enter case more than 1/4". May need to set RADIO VOLUME ADJUST inside the unit before final mounting and installation A microphone c...
Este manual também é adequado para os modelos :Avtousiliteli - SA-400-83 (55.49 kb)
Avtousiliteli - SA-400-83 28V (55.49 kb)