Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
RADIO VOLUME ADJUST The RADIO VOLUME ADJUST is a one time setting which depends on the radio connected and its normal volume. The siren cover must be removed to access the adjustment. The cover is held in place by a snap-fastener on the back of the unit. While holding the case on the sides press hard with your thumbs on the back of the unit. The chassis will slide out the front. Switch siren to RADIO mode and turn on the power. With the volume on the radio itself set to normal level, set the RADIO VOLUME ADJUST to the RADIO VOLUME ADJUST desired level. Turn off power and press the chassis back into the cover. TB0324B Page 5 of 7 10/18/03 SERVICE This unit is designed to provide years of reliable service under even the worst conditions. Many times there may appear to be a problem with the unit when the true problem is in the speaker(s) or improper installation. The following chart shows typical symptoms and possible causes. A blown rear panel fuse doesn't necessarily mean that the unit is bad. If a speaker or speaker lead is shorted this fuse will blow before the unit is damaged. Disconnect the SPKR leads and replace the fuse. If the siren emits a sound when in the Yelp position it is OK. Check the speaker(s) or leads for possible shorting. PROBLEMS Symptom Possible Cause Check No Power or siren output Power switch not turned on Bad Speaker Connector or connections loose Rear panel fuse blown Loose connection at power source Does backlighting come on? Do you hear a “pop” when turned on? With siren on, yelp selected, listen for tone in amplifier. Is an external fuse or circuit breaker used? Are the power leads connected to a good buss? No siren tone – PA works High Voltage Protection Mic Button stuck The input voltage must be less than highest rating. Does Mic Button release properly? No PA PA volume not set properly Function switch in Radio Try turning the PA volume control. PA is not available in Radio position. Distorted siren sound Speaker assembly loose Intermittent Aux Input connection Low Vehicle voltage Is the speaker bell or tip loose? Is the Aux Input used and wired properly? The input voltage must be greater than lowest rating. Intermittent siren tone High Voltage Protection Connector loose Loose connection at power source Mic Button activation Circuit breaker in supply connection Is the vehicle voltage regulator working properly? Is the connector tight on the back of the unit? Check for loose leads back to power source. Is something lying on the microphone? Is a circuit breaker used with at least 50A rating? Horn or manual stuck on Siren switch stuck Aux Input improperly connected Does the Siren pushbutton switch return fully when released? Is the Aux Input used and wired properly? No Radio Unit not connected to a radio Radio volume too low Is the radio connected properly to the unit? Can you hear the radio in the vehicle? Try adjusting the internal radio volume control. RETURN If you have any questions concerning this or any other Carson product, please contact our Technical Service Department at (888) 577-6877. Many issues can be handled over the phone. We can also be reached via e-mail at service@carsonsirens.com If a product must be returned for any reason, please contact our Technical Service Department to obtain a Returned Merchandise Authorization number (RMA#) before you ship the product to Carson. Please write the RMA# clearly on the package near the mailing label. Be sure to provide a return address, contact and phone number, along with a brief description of the problem. TB0324B Page 6 of 7 10/18/03 PARTS 2 4 9 1 10 8 SA400 SA400SA400 RADIO RADIORADIO SIREN SIRENSIREN 7 HORN HORNHORN PA PAPA VOL VOLVOL 12 MAN MANMAN WAIL WAILWAIL YELP YELPYELP ON ONON OFF OFFOFF PHASER PHASERPHASER 11 13 5 3 6 Item Part # Description 1 CP3687 Bezel, front panel for SA-400-73,83 CP3966 Bolt, mounting, 1/4-20 X 3/8 (2 required) CP3571 Bracket, mounting 2 8025 DRS/CAP Button, red w/ dress nut (C&K #801803000 Cap, #702501201 Nut) (for pushbutton switch) 3 CP3883 Cable, internal chassis plug wiring harness CP2560 Cable, external wiring harness 4 CP3547 Control, PA volume (350 ohm) 5 ES00026-03 Cover with stud 6 CP3408 Fuse holder 7 CP4852 Knob, rotary function switch 8 CP4853 Knob, PA volume control 9 CP3688 Label, front panel for SA-400-73,83 #73 LAMP Lamp, T-1-3/4 14V Mini Wedge Base (JKL #73) (used on SA-400-83 14,PG) E85 LAMP Lamp, T-1-1/2 28V Mini Wedge Base (JKL #E85) (used on SA-400-83 28) CP3570 Microphone CP3633 Microphone clip with mounting screws 10 CP3692 Switch, pushbutton siren (C&K #8121SD2A2GE, must cut off tabs) 11 2FA53-73 Switch, toggle power (Carling Switch #2FA53-73) 12 CP3548 Switch, rotary function (top tabs folded and soldered) 13 CP4119 Transistor, output (2 required) (Industry standard TIP36C, Not Texas Instruments) TB0324B Page 7 of 7 10/18/03 ...
Este manual também é adequado para os modelos :Avtousiliteli - SA-400-83 (55.49 kb)
Avtousiliteli - SA-400-83 14V (55.49 kb)